Property types reference

This table lists all default property types available in Kanzi. See Property system, Creating property types, and Node and resource reference.

Name	Display Name	Inherited	Attachable	Description
Action.Delay	Action Delay (ms)	No	No	The time in milliseconds after which Kanzi invokes the action.
ActivityConcept.ActivityMessageArguments.ActivityName	Activity Name	No	No
ActivityConcept.SaveLastFocusedNode	Save Last Focused Node	No	Yes	When this property is enabled, Kanzi remembers the last-focused node in this Activity and sets the keyboard focus to that node when you activate this Activity again. This is the default. When you do not want Kanzi to remember the last-focused node in this Activity, disable this property.
ActivityConcept.Status	Activity Status	No	Yes	Sets the possible states of the Activity when its Activity Host activates or deactivates that Activity.
ActivityConcept.StatusChangedMessageArguments.Status	Activity Status	No	No	The possible states of an Activity when its Activity Host activates or deactivates that Activity.
ActivityHostConcept.ActivationMessageArguments.ActivationPath	Activity Activation Path	No	No	The relative path from the target Activity Host to the Activity that you want to activate.
ActivityHostConcept.ActivityPrefabMessageArguments.ActivityName	Activity Name	No	No	The name of the child Activity whose prefab was attached or detached.
AlphaCutoff	Alpha Cutoff	No	Yes	Sets the cutoff threshold for alpha cutting. If the alpha value is less than the value of this property, Kanzi discards the fragment. The default value is 0.5.
Ambient	Ambient Color	No	Yes	The color of the material when lights are not present.
AnimationBindingProcessor.Animation	Animation Item Path	No	No	The animation binding processor applies this animation when the binding is updated.
AnimationPlayer.AutoplayEnabled	Autoplay Enabled	No	No	Specifies whether animation player should start playback of its timeline automatically when it is attached to the node.
AnimationPlayer.DurationScale	Duration Scale	No	No	Specifies how much duration of the timeline is scaled during its playback.
AnimationPlayer.PlaybackMode	Playback Mode	No	No	Specifies the mode of timeline playback (normal, reverse, pingpong).
AnimationPlayer.PlayMessageArguments.DurationScale	Duration Scale	No	No	Specifies how much duration of the timeline is scaled during its playback. This scale is applied on top of player's duration scale property.
AnimationPlayer.PlayMessageArguments.PlaybackMode	Playback Mode	No	No	Specifies the mode of timeline playback (normal, reverse, pingpong). This mode is applied on top of player's mode property.
AnimationPlayer.PlayMessageArguments.RepeatCount	Repeat Count	No	No	Specifies how many times the timeline is played during its playback (1 for one time playback, 0 for infinite amount of repeats). This repeat count is applied on top of player's repeact count property.
AnimationPlayer.RelativePlayback	Relative Playback	No	No	Specifies whether animations are played in relative manner by adding animated value to target property value instead of replacing the property value.
AnimationPlayer.RepeatCount	Repeat Count	No	No	Specifies how many times the timeline is played during its playback (1 for one time playback, 0 for infinite amount of repeats).
AnimationPlayer.RestoreOriginalValuesAfterPlayback	Restore Original Values After Playback	No	No	Specifies whether animated properties return to their initial values after playback of the timeline ends.
AnimationPlayer.Timeline	Target Animation Timeline	No	No	The target animation timeline.
ApplyActivationAction.ActivationPath	Activity Activation Path	No	No	The activation path from the Activity Host, which is set as the target of this action, to the Activity node you want to activate. The activation path contains only the Activity nodes and the Activity Hosts nodes.
ApplyActivationAction.ActivityHostPath	Activity Host Path	No	No	Path to the Activity Host node of the activated Activity node.
BaseColorFactor	Base Color Factor	No	Yes	Sets the base color for the material.
BaseColorTexture	Base Color Texture	No	Yes	Sets the texture that contains the base color for the material. Use the Base Color Factor property to filter the value from this texture.
BindingItem.TargetPropertyType	Target Property	No	Yes	The binding target property
BindingSourceItem.PropertyType	Source Property	No	Yes	The binding source property
BlendIntensity	Blend Intensity	No	Yes	Controls the intensity of materials that are blended on top of an existing color. Attached property enables overriding of the blend intensity of the used materials at render pass or object node level.
BlendMode	Blend Mode	No	Yes	Sets how to blend colors: Opaque disables blending and replaces the destination pixels with the source pixels. Additive adds the source pixels to the destination pixels. Multiply multiplies the source and destination pixels. Screen adds the source and destination pixels and subtracts from the result the product of the source and destination. Alpha: Automatic uses premultiplied or non-premultiplied alpha depending on the value of the "Premultiply Alpha" property in the project or an image. Alpha: Non-premultiplied is a legacy mode. For non-premultiplied input use the Alpha: Mixed mode. Alpha: Premultiplied expects premultiplied alpha RGBA in the source pixels and blends the source pixels on top of the destination pixels. This is the default and recommended mode for alpha blending. Alpha: Mixed expects non-premultiplied alpha RGBA in the source pixels, and blends the source pixels with the destination framebuffer. Clear sets the destination pixels to transparent black. Exclusive Or draws the non-overlapping source and destination pixels. Source Atop discards those source pixels that do not cover destination pixels and draws the rest of the source pixels over destination pixels. Source In draws those source pixels that cover destination pixels and discards all destination pixels. Source Out draws the source pixels with alpha reduced by the inverse of the destination alpha, and discards all destination pixels. Destination Atop discards those destination pixels that are not covered by source pixels, and draws the rest of the destination pixels over source pixels. Destination In draws only those destination pixels that intersect with the source pixels, and discards all source pixels. Destination Out draws the destination pixels with alpha reduced by the inverse of the source alpha, and discards all source pixels. Destination Over draws the destination pixels over the source pixels.
BlitRenderPass.Material	Material	No	Yes	Sets to the Material that you want a Blit Render Pass to use to blit one or more textures.
BlitRenderPass.Texture0	Texture 0	No	Yes	Sets the first texture you want the Blit Render Pass to blit.
BlitRenderPass.Texture1	Texture 1	No	Yes	Sets the second texture you want the Blit Render Pass to blit.
BlitRenderPass.Texture2	Texture 2	No	Yes	Sets the third texture you want the Blit Render Pass to blit.
BlitRenderPass.Texture3	Texture 3	No	Yes	Sets the fourth texture you want the Blit Render Pass to blit.
BlurEffect2D.Masked	Masked Blur	No	Yes	Sets whether to blur only the pixels whose alpha channel value is not zero. When you enable this property, the blur does not spread to fully transparent pixels and the edges of the content stay sharp. The default value is false.
BlurEffect2D.Quality	Blur Quality	No	Yes	Sets the visual quality of the blur. Lower quality uses less computing and memory resources.
BlurEffect2D.Radius	Blur Radius	No	Yes	Sets the amount of blur by defining the radius of the circular area of pixels that blend into each other. The blur radius also determines the distance in pixels that the blur expands the render area by extending outward from an edge, unless you enable the Masked Blur property. To disable the blur effect, set this property to 0. The default value is 8.
BrdfLookUpTable	BRDF Lookup Table	No	Yes	Gets the Bidirectional Reflectance Distribution Function (BRDF) lookup table for the material. The BRDF table is a texture that contains precomputed information about how light reflects off a material. You can use it to improve rendering quality.
Brush.BrushType	Brush Type	No	Yes	The type of the brush.
Brush.HorizontalTiling	Brush Horizontal Tiling	No	Yes	Horizontal Tiling for the brush. Affects the scale of texture coordinates.
Brush.ModulateColor	Brush Modulate Color	No	Yes	Modulation color for brush. Effects brush rendering that needs color modulation.
Brush.VerticalTiling	Brush Vertical Tiling	No	Yes	Vertical Tiling for the brush. Affects the scale of texture coordinates.
ButtonConcept.AutoClickInterval	Auto Press Interval	No	Yes	Sets the time in milliseconds after which a button that the user keeps pressed down sends the Button: Click message. While the user holds the button down, the button keeps sending the Button: Click message at the time interval set by this property. To disable the behavior, set to 0.
ButtonConcept.IndexInGroup	Index In Group	No	Yes	Sets the index of the Button in the Toggle Button Group to which that Button is registered. If a Button does not have local value for this property, it is not registered to the ancestor Toggle Button Group. When set to -1 the Toggle Button Group assigns an index for the Button.
ButtonConcept.IsPressed	Is Down	No	Yes	Indicates whether the button is pressed and in the down state.
ButtonConcept.LongPressInterval	Hold Interval	No	Yes	Sets the amount of time in milliseconds that the user must hold the button pressed down for Kanzi to recognize it as a long-press gesture. To disable the long-press gesture, set to 0.
ButtonConcept.PressOnHover	Down On Hover	No	Yes	Whether holding a finger on the device screen and moving it over the button transitions the button to the down state.
ButtonConcept.ToggleState	Toggle State	No	Yes	Sets the toggle state of the Button.
ButtonConcept.ToggleStateCount	Toggle State Count	No	Yes	Sets the number of toggle states of the Button.
Camera.AspectRatio	Aspect Ratio	No	Yes	The aspect ratio of the camera.
Camera.AsymmetricFov	Asymmetric FOV	No	Yes	The field of view of the camera in degrees. Angles are in order left, right, up, and down. Angles to the right of the center and upwards of the center are positive.
Camera.DisableAspectRatio	Use Viewport Aspect Ratio	No	Yes	Whether to use the aspect ratio setting from the viewport in render pass. If not, you can set the aspect ratio in the camera.
Camera.Fov	FOV	No	Yes	The field of view of the camera in degrees.
Camera.FovType	FOV Type	No	Yes	Defines the direction of the field of view to either x or y.
Camera.OrthogonalCoordinateSystemType	Orthogonal Type	No	Yes	Defines the type of the orthogonal coordinate system. In the absolute mode the camera uses pixel coordinates. In the relative mode the camera displays an area whose width is -1..1 scaled with the value set by the Orthogonal Plane Size property.
Camera.OrthogonalPlaneHeight	Orthogonal Plane Size	No	Yes	The value used for scaling the view area of a relative orthographic camera.
Camera.ProjectionType	Projection Type	No	Yes	Defines the camera type to either perspective or orthographic camera.
Camera.ZFar	Z Far	No	Yes	The distance of the camera far clipping plane. The camera shows only the objects that are closer than the value set in this property.
Camera.ZNear	Z Near	No	Yes	The distance of the camera near clipping plane. The camera shows only the objects that are farther away than the value set in this property.
ClearCoatNormalScale	Clear Coat Normal Scale	No	Yes	Sets the clear coat normal scale for the material. Use the scale to set the intensity of the Clear Coat Normal Texture.
ClearCoatNormalTexture	Clear Coat Normal Texture	No	Yes	Sets the texture that contains a clear coat normal map for the material. Use the Clear Coat Normal Scale property to scale the texture value.
ClearCoatRoughnessFactor	Clear Coat Roughness Factor	No	Yes	Sets the roughness of the outer clear coat layer for the material: 0 represents a smooth, glossy surface, and 1 represents a rough, diffuse surface.
ClearCoatRoughnessTexture	Clear Coat Roughness Texture	No	Yes	Sets the texture that contains a clear coat roughness map for the material. Kanzi reads the roughness from the Green channel of the texture. Use the Clear Coat Roughness Factor property to scale the roughness from this texture.
ClearCoatStrengthFactor	Clear Coat Strength Factor	No	Yes	Sets the clear coat strength for the material: 0 represents a material with no clear coat, and 1 represents a full strength clear coat.
ClearCoatStrengthTexture	Clear Coat Strength Texture	No	Yes	Sets the texture that contains a clear coat strength map for the material. Kanzi reads the strength from the Red channel of the texture. Use the Clear Coat Strength Factor property to scale the strength from this texture.
ClearRenderPass.ClearColor0	Clear Color 0	No	Yes	Sets the color that you want the Clear Render Pass to use to clear the first (default) color buffer.
ClearRenderPass.ClearColor1	Clear Color 1	No	Yes	Sets the color that you want the Clear Render Pass to use to clear the second color buffer.
ClearRenderPass.ClearColor2	Clear Color 2	No	Yes	Sets the color that you want the Clear Render Pass to use to clear the third color buffer.
ClearRenderPass.ClearColor3	Clear Color 3	No	Yes	Sets the color that you want the Clear Render Pass to use to clear the fourth color buffer.
ClearRenderPass.ClearDepth	Clear Depth	No	Yes	Sets the depth that you want the Clear Render Pass to use to clear the depth buffer.
ClearRenderPass.ClearStencil	Clear Stencil	No	Yes	Sets the clear stencil that you want the Clear Render Pass to use to clear the stencil buffer.
ClickConcept.DoubleClickEnabled	Double-Click Enabled	No	Yes	Whether to install a multi-click manipulator that generates double-click messages. Use this property to enable the double-click gesture for a Button node or List Box items. To enable double-click for List Box items, enable this property in the List Box Item Container.
CodeBehind.CodeBehindSource	Code Behind Source	No	Yes	Sets the metaclass name of the code behind class for this node.
ColorBrush.Color	Brush Color	No	Yes	Color for brush. Set alpha to 0 to disable brush.
Command.CommandMessageArguments.CommandArgumentProperty	Command	No	No	The command argument executed by a UI control
Command.CommandProperty	Command	No	Yes	The command executed by a UI control
ComposerFactoryName	Engine Factory Name	No	Yes	The factory name for this composer. Can be used to instantiate composer or render pass from plugin.
CompositionTargetRenderPass.AddressingMode	Addressing Mode	No	Yes	Sets how Kanzi handles the texture coordinates of the automatically generated composition target textures outside of the [0, 0] - [1, 1] rectangle: - Repeat sets the texture to repeat outside of these coordinates. This is the default value. - Mirror sets the texture to repeat, but mirrors every other repetition. - Clamp confines the texture to these coordinates and outside of these texture coordinates repeats the edge texels of the texture. -Mirror once sets the texture to repeat once in the negative direction, and after that clamps the texture.
CompositionTargetRenderPass.CompositionTarget0	Composition Target 0	No	Yes	Sets the first color target to which you want to render the result of the child render passes of this render pass.
CompositionTargetRenderPass.CompositionTarget1	Composition Target 1	No	Yes	Sets the second color target to which you want to render the result of the child render passes of this render pass.
CompositionTargetRenderPass.CompositionTarget2	Composition Target 2	No	Yes	Sets the third color target to which you want to render the result of the child render passes of this render pass.
CompositionTargetRenderPass.CompositionTarget3	Composition Target 3	No	Yes	Sets the fourth color target to which you want to render the result of the child render passes of this render pass.
CompositionTargetRenderPass.DepthCompareFunction	Depth Compare Function	No	Yes	Sets the comparison function to be used with comparison samplers of the Composition Target Render Pass' depth target.
CompositionTargetRenderPass.DepthTarget	Depth Target	No	Yes	Sets the depth target to which you want to render the result of the child render passes of this render pass.
CompositionTargetRenderPass.DepthTextureFormat	Depth Texture Format	No	Yes	Sets the format of the automatically created Result Depth Texture.
CompositionTargetRenderPass.FilterMode	Filter Mode	No	Yes	Sets how Kanzi handles accessing the texture samples of the automatically generated composition target: - Nearest takes the color from the nearest sample. - Linear interpolates color from neighboring samples. This is the default value.
CompositionTargetRenderPass.Height	Height	No	Yes	Sets the absolute height for the automatically created composition target textures. If this property is not set, the size is taken from the current composition stack state using the values of the Resolution Multiplier and Resolution Divisor properties.
CompositionTargetRenderPass.MipmapMode	Mipmap Mode	No	Yes	Sets the mipmap mode of the automatically created composition target. To enable mipmaps set the property value to Linear or Nearest. Enabling mipmaps introduces the runtime cost of generating mipmaps after rendering. To disable mipmaps remove the property.
CompositionTargetRenderPass.MultisampleLevel	Multisample Level	No	Yes	Sets the number of samples you want to use for each output pixel of the automatically generated composition target textures. To disable multisampling, remove the property or set the property value to 1.
CompositionTargetRenderPass.PixelFormat0	Pixel Format 0	No	Yes	Sets on the GPU the target pixel format of the first automatically created composition target texture.
CompositionTargetRenderPass.PixelFormat1	Pixel Format 1	No	Yes	Sets on the GPU the target pixel format of the second automatically created composition target texture.
CompositionTargetRenderPass.PixelFormat2	Pixel Format 2	No	Yes	Sets on the GPU the target pixel format of the third automatically created composition target texture.
CompositionTargetRenderPass.PixelFormat3	Pixel Format 3	No	Yes	Sets on the GPU the target pixel format of the fourth automatically created composition target texture.
CompositionTargetRenderPass.ResolutionDivisor	Resolution Divisor	No	Yes	Sets the resolution divisor for the automatically created composition target textures. Together with the Resolution Multiplier property this property sets the size of the composition target in relation to the size of the current Viewport 2D node. For more fine-grained control, bind from the InputViewport property to Width and Height properties.
CompositionTargetRenderPass.ResolutionMultiplier	Resolution Multiplier	No	Yes	Sets the resolution multiplier for the automatically created composition target textures. Together with the Resolution Divisor property this property sets the size of the composition target in relation to the size of the current Viewport 2D node. For more fine-grained control, bind from the InputViewport property to Width and Height properties.
CompositionTargetRenderPass.ResolveImmediately	Resolve Immediately	No	Yes	Whether to resolve multisamples and generate mipmaps for the composition target texture immediately after rendering. By default the Composition Target Render Pass resolves multisamples and generates mipmaps immediately. When you continue rendering to the composition target in another Composition Target Render Pass that performs the resolve, disable this property.
CompositionTargetRenderPass.ResultDepthTexture	Result Depth Texture	No	Yes	The depth texture to which the Composition Target Render Pass renders its content.
CompositionTargetRenderPass.ResultTexture0	Result Texture 0	No	Yes	The first color texture to which the Composition Target Render Pass renders its content.
CompositionTargetRenderPass.ResultTexture1	Result Texture 1	No	Yes	The second color texture to which the Composition Target Render Pass renders its content.
CompositionTargetRenderPass.ResultTexture2	Result Texture 2	No	Yes	The third color texture to which the Composition Target Render Pass renders its content.
CompositionTargetRenderPass.ResultTexture3	Result Texture 3	No	Yes	The fourth color texture to which the Composition Target Render Pass renders its content.
CompositionTargetRenderPass.Width	Width	No	Yes	Sets the absolute width for the automatically created composition target textures. If this property is not set, the size is taken from the current composition stack state using the values of the Resolution Multiplier and Resolution Divisor properties.
ConstraintInWorldCoordinates	Constraint In World Coordinates	No	Yes	Specifies if the object constraining is done in world coordinates (when false, done in local coordinates).
ConstraintOrientation	Constraint Orientation	No	Yes	Makes an object node where the property is attached to obtain orientation from target object
ConstraintPosition	Constraint Position	No	Yes	Makes an object node where the property is attached to obtain position from target object
ContentLayoutConcept.DepthPadding	Depth Padding	No	Yes	Sets the padding spaces between the content and the front and back boundaries of the Content Layout 3D node.
ContentLayoutConcept.HorizontalPadding	Horizontal Padding	No	Yes	Sets the padding spaces between the content and the left and right boundaries of the Content Layout node.
ContentLayoutConcept.VerticalPadding	Vertical Padding	No	Yes	Sets the padding spaces between the content and the top and bottom boundaries of the Content Layout node.
CubeMapRenderPass.CompositionTarget	Composition Target	No	Yes	Sets the target to which you want to render the result of this Cubemap Render Pass.
CubeMapRenderPass.DepthCompareFunction	Depth Compare Function	No	Yes	Sets the comparison function to be used with comparison samplers of the Cubemap Render Pass' depth target.
CubeMapRenderPass.DepthFormat	Depth Format	No	Yes	Sets the format of the automatically created depth render buffer used for the cubemap rendering. If this property is not set, the depth requirement and format are autodetected.
CubeMapRenderPass.FilterMode	Filter Mode	No	Yes	Sets how Kanzi handles accessing the texture samples of the automatically generated composition cubemap target: - Nearest takes the color from the nearest sample. - Linear interpolates color from neighboring samples. This is the default value.
CubeMapRenderPass.MipmapMode	Mipmap Mode	No	Yes	Sets the mipmap mode of the automatically created composition cubemap target. To enable mipmaps set the property value to Linear or Nearest. Enabling mipmaps introduces the runtime cost of generating mipmaps after rendering. To disable mipmaps remove the property.
CubeMapRenderPass.OverrideCamera	Override Camera	No	Yes	Sets the Camera node that you want to use to render the nodes to the composition cubemap texture. To use the default Camera node in that Scene node, do not set the value for this property.
CubeMapRenderPass.PixelFormat	Pixel Format	No	Yes	Sets on the GPU the target pixel format of the automatically created composition cubemap target textures.
CubeMapRenderPass.Resolution	Resolution	No	Yes	Sets the dimensions of the automatically created composition cubemap target textures. The default value is 64.
CubeMapRenderPass.ResolveImmediately	Resolve Immediately	No	Yes	Whether to generate mipmaps for the composition target texture immediately after rendering. By default the Cubemap Render Pass generates mipmaps immediately. When you continue rendering to the composition target in another Cubemap Render Pass that performs the resolve, disable this property.
CubeMapRenderPass.ResultDepthTexture	Result Depth Texture	No	Yes	The cubemap depth texture to which the Cubemap Render Pass renders its content.
CubeMapRenderPass.ResultTexture	Result Texture	No	Yes	The result cubemap texture that was rendered to by the Cubemap Render Pass.
CustomAssetThumbnail	Custom Asset Thumbnail	No	Yes	When enabled, the asset will have selected image as thumbnail instead of the generated one.
DataContext.DataContext	Data Context	No	Yes	Source of data for this node and its descendants
DataContext.ItemsSource	Items Source	No	Yes	Data object which provides data sources for list items.
DataDrivenExclusiveActivityHostConcept.ActiveActivityIndex	Active Activity Index	No	Yes	The index of the active Activity in the Data-Driven Exclusive Activity Host. After instantiating all Activity from a Data Source, this property refers to the only currently active Activity in this Data-Driven Exclusive Activity Host. To deactivate all the Activities in this Data-Driven Exclusive Activity Host, set this property to -1.
DataDrivenExclusiveActivityHostConcept.ActivitySource	Activity Source	No	Yes	The data object that provides the data for this Activity node.
DataDrivenExclusiveActivityHostConcept.ActivityTemplate	Activity Template	No	Yes	If set, the Data-Driven Exclusive Activity Host uses this prefab for Activity nodes that it creates.
DataObjectValue	Value	No	Yes	The last read value of the data object
Description	Description	No	Yes	Add a description of the purpose of this item. To export descriptions to a plain text file, select File > Export > Export Descriptions. When you export the kzb file, this description is not included in the exported file.
DetailBaseColorFactor	Detail Base Color Factor	No	Yes	Sets the detail base color for the material. The detail base color is alpha blended with the standard base color.
DetailBaseColorTexture	Detail Base Color Texture	No	Yes	Sets the detail texture that contains the base color for the material. Use the Detail Base Color Factor property to filter the value from this texture. The detail base color is alpha blended with the standard base color. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailClearCoatNormalScale	Detail Clear Coat Normal Scale	No	Yes	Sets the detail clear coat normal scale for the material. Use the scale to set the intensity of the Detail Clear Coat Normal Texture.
DetailClearCoatNormalTexture	Detail Clear Coat Normal Texture	No	Yes	Sets the detail texture that contains a clear coat normal map for the material. Use the Detail Clear Coat Normal Scale property to scale the texture value.
DetailClearCoatRoughnessTexture	Detail Clear Coat Roughness Texture	No	Yes	Sets the detail texture that contains a clear coat roughness map for the material. Use the Clear Coat Roughness Factor and Clear Coat Roughness Texture properties to scale the roughness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailClearCoatStrengthTexture	Detail Clear Coat Strength Texture	No	Yes	Sets the detail texture that contains a clear coat strength map for the material. Kanzi reads the strength from the Red channel of the texture. Use the Clear Coat Strength Factor and Clear Coat Strength Texture properties to scale the strength from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailDiffuseFactor	Detail Diffuse Color Factor	No	Yes	Sets the detail diffuse color for the material. Kanzi alpha blends the detail diffuse color with the standard diffuse color.
DetailDiffuseTexture	Detail Diffuse Color Texture	No	Yes	Sets the detail texture that contains the diffuse color for the material. Use the Detail Diffuse Color Factor property to filter the value from this texture. Kanzi alpha blends the detail diffuse color with the standard diffuse color. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailEmissiveFactor	Detail Emissive Factor	No	Yes	Sets the color of the light that is emitted from a detail texture for the material. This color affects the local material rendering, but the light is not cast to other objects. The detail emissive light is alpha blended with the standard emissive light. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailEmissiveTexture	Detail Emissive Texture	No	Yes	Sets the detail texture that contains the light emitted from the material. Use the Detail Emissive Factor property to scale the value from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailGlossinessTexture	Detail Glossiness Texture	No	Yes	Sets the detail texture that contains a glossiness map for the material. Kanzi reads the glossiness from the Alpha channel of this texture. Use the Glossiness Factor and Glossiness Texture properties to scale the glossiness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailMetallicTexture	Detail Metallic Texture	No	Yes	Sets the detail texture that contains a metallic map for the material. Kanzi reads the metalness from the Blue channel of this texture. Use the Metallic Factor and Metallic Texture properties to scale the metalness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailNormalScale	Detail Normal Scale	No	Yes	Sets the detail normal scale for the material. Use the scale to set the intensity of the Detail Normal Texture.
DetailNormalTexture	Detail Normal Texture	No	Yes	Sets the detail texture that contains a normal map for the material. Use the Detail Normal Scale property to scale the texture value.
DetailOcclusionStrength	Detail Occlusion Strength	No	Yes	Sets the detail occlusion strength for the material. Use the strength to set the intensity of the Detail Occlusion Texture.
DetailOcclusionTexture	Detail Occlusion Texture	No	Yes	Sets the detail texture that contains an occlusion map for the material. Kanzi reads the occlusion from the Red channel of this texture. Use the Detail Occlusion Strength property to scale the occlusion from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailRoughnessTexture	Detail Roughness Texture	No	Yes	Sets the detail texture that contains a roughness map for the material. Kanzi reads the roughness from the Green channel of the texture. Use the Roughness Factor and Roughness Texture properties to scale the roughness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailSpecularFactor	Detail Specular Color Factor	No	Yes	Sets the detail specular color for the material. Kanzi alpha blends the detail specular color with the standard specular color.
DetailSpecularTexture	Detail Specular Color Texture	No	Yes	Sets the detail texture that contains the specular color for the material. Use the Detail Specular Color Factor property to filter the value from this texture. Kanzi alpha blends the detail specular color with the standard specular color. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.
DetailTextureOffset	Detail Texture Offset	No	Yes	Sets the detail texture offset for the material. Kanzi adds this value to the UVs to produce a second set of detail UVs to use for all detail texture properties.
DetailTextureTiling	Detail Texture Tiling	No	Yes	Sets the detail texture tiling factor for the material. Kanzi multiplies this value by the UVs to produce a second set of detail UVs to use for all detail texture properties.
Diffuse	Diffuse Color	No	Yes	The color of the material when it is lit by a light.
DiffuseFactor	Diffuse Color Factor	No	Yes	Sets the diffuse color for the material.
DiffuseTexture	Diffuse Color Texture	No	Yes	Sets the texture that contains the diffuse color for the material. Use the Diffuse Color Factor property to filter the value from this texture.
DirectionalLight	Directional Light	No	Yes	Directional light settings
DirectionalLightColor	Directional Light Color	No	Yes	Sets the color of the Directional Light.
DispatchMessageAction.DefineTargetWithProperty	Define Target with Property	No	Yes	Define Target with Property
DispatchMessageAction.RoutingTarget	Target Item	No	No	Specifies the target item to which the message is dispatched. If the target resides within the node tree, and the message type has tunneling and bubbling enabled, the message is tunneled and bubbled through the parents of the target.
DispatchMessageAction.RoutingTargetLookup	Property	No	No	Allows to look up the target item using this property (RoutingTarget.Property).
DockLayoutConcept.LastItemFill	Last Item Fill	No	Yes	Whether the last item of the dock layout is given the remaining free space.
DockLayoutConcept.Side	Side	No	Yes	The docking side of an item in the dock layout.
DrawObjectsRenderPass.CameraMatrix	Calculated Camera Matrix	No	Yes	Camera matrix calculated during DrawObjectsRenderPass rendering.
DrawObjectsRenderPass.DirectionalLights	Directional Lights	No	Yes	Use this property to bind the directional light set for rendering.
DrawObjectsRenderPass.FrustumCullingEnabled	Frustum Culling	No	Yes	Enable to disable rendering objects that are not inside the view frustum. Trades GPU rendering time for CPU cull test time.
DrawObjectsRenderPass.NearFarPlane	Calculated Projection Near / Far Planes.	No	Yes	Near / far planes calculated during DrawObjectsRenderPass rendering.
DrawObjectsRenderPass.ObjectSource	Object Source	No	Yes	Sets the object source which collects the nodes that you want to render with this render pass. To render all nodes in a Scene node (Root Object Source), do not set the value for this property.
DrawObjectsRenderPass.PointLights	Point Lights	No	Yes	Use this property to bind the point light set for rendering.
DrawObjectsRenderPass.ProjectionMatrix	Calculated Projection Matrix	No	Yes	Projection matrix calculated during DrawObjectsRenderPass rendering.
DrawObjectsRenderPass.SpotLights	Spot Lights	No	Yes	Use this property to bind the spot light set for rendering.
DrawObjectsRenderPass.Viewport	Rendering Viewport	No	Yes	Viewport applied by DrawObjectsRenderPass rendering.
DrawObjectsWithMaterialRenderPass.Material	Material	No	Yes	Sets the material that will be used to render all nodes rendered by this DrawObjectsWithMaterialRenderPass.
EffectFactoryName	Effect Factory Name	No	Yes	The factory name for the effect. Use this name to instantiate an effect from a plugin.
Emissive	Emissive Color	No	Yes	The color of the light that is emitted from the material surface.
EmissiveFactor	Emissive Factor	No	Yes	Sets the color of the light that is emitted from the material. This color affects the local material rendering, but the light is not cast to other objects.
EmissiveTexture	Emissive Texture	No	Yes	Sets the texture that contains the light emitted from the material. Use the Emissive Factor property to scale the value from this texture.
EnvironmentAmbientFactor	Environment Ambient Factor	No	Yes	Sets the strength of the cubemap texture to use for ambient environment light. Use the Environment Ambient Texture property to set the cubemap texture. The ambient environment light affects diffuse lighting in image based lighting.
EnvironmentAmbientTexture	Environment Ambient Texture	No	Yes	Sets the cubemap to use for the ambient environment light for the material. This cubemap affects the diffuse lighting during image based lighting. Use the Environment Ambient Factor property to set the strength of the cubemap texture.
EnvironmentReflectionFactor	Environment Reflection Factor	No	Yes	Sets the strength of the cubemap texture to use for specular environment light. Use the Environment Reflection Texture property to set the cubemap texture. The specular environment light affects reflective lighting in image based lighting.
EnvironmentReflectionTexture	Environment Reflection Texture	No	Yes	Sets the cubemap to use for the specular environment light for the material. This cubemap affects reflective lighting during image based lighting. Use the Environment Reflection Factor property to set the strength of the cubemap texture.
ExclusiveActivityHostConcept.ImplicitActivityChangeRequestMessageArguments.LoopActivity	Loop Activity	No	No	Sets how an Exclusive Activity Host reacts to the 'Navigate To Next Activity' and 'Navigate To Previous Activity' messages when it reaches its last and first Activities. When set to true and an Exclusive Activity Host reaches: - The last Activity, the Exclusive Activity Host reacts to the 'Navigate To Next Activity' message by activating the first Activity in that Exclusive Activity Host. - The first Activity, the Exclusive Activity Host reacts to the 'Navigate To Previous Activity' message by activating the last Activity in that Exclusive Activity Host.
Exposure	Exposure	No	Yes	Sets the exposure compensation for the material. The exposure compensation emulates camera exposure by controlling the total amount of light rendered. Use a negative value to darken the rendered image, and a positive value to lighten the image. Exposure is exponential: 1.0 is twice as bright as 0.0, and -1.0 is half as bright as 0.0.
ExpressionBindingProcessor.Argument1	Argument 1	No	No	The first argument in the binding expression.
ExpressionBindingProcessor.Argument1Field	Argument 1 Field	No	No	The property attribute for the first argument.
ExpressionBindingProcessor.Argument2	Argument 2	No	No	The second argument in the binding expression.
ExpressionBindingProcessor.Argument2Field	Argument 2 Field	No	No	The property attribute for the second argument.
ExpressionBindingProcessor.Argument3	Argument 3	No	No	The third argument in the binding expression.
ExpressionBindingProcessor.Argument3Field	Argument 3 Field	No	No	The property attribute for the third argument.
ExpressionBindingProcessor.Operation	Operation	No	No	The operation in the expression.
ExpressionBindingProcessor.Output	Output	No	No	The temporary register to write the result to.
ExpressionBindingProcessor.OutputField	Output Field	No	No	The property attribute of the output register.
FaceToCameraMode	Face to Camera Mode	No	Yes	Sets how to rotate the 3D node towards a camera: - Disabled does not make the node turn to the camera. - Look at rotates the node along all axes to turn to the camera. - Billboarding keeps the node perpendicular to the camera FOV. - Cylindrical rotates the node along the y axis to turn to the camera. By default the node turns to the Scene default camera. To use a different camera, set the Face to Camera Target Camera property.
FaceToCameraTargetCamera	Face to Camera Target Camera	No	Yes	Sets the camera towards which the 3D node turns when you set the Face to Camera Mode property. The default is the Scene default camera.
FloatValueAccumulator.IncrementSize	Increment Size	No	No	The size of the increments of this Float Value Accumulator.
FloatValueAccumulator.IncrementSizeSource	Increment Size Source	No	No	The property type set on this node that determines the increment size of this Float Value Accumulator.
FloatValueAccumulator.MaximumAccumulatedValue	Maximum Value	No	No	The maximum total accumulated float value.
FloatValueAccumulator.MinimumAccumulatedValue	Minimum Value	No	No	The minimum total accumulated float value.
FloatValueAccumulator.TargetPropertyField	Target Property Field	No	No	The field of the target property on a node which where the values of the input property are accumulated.
FloatValueAccumulator.TargetPropertyType	Target Property Type	No	No	The property type on this node that this Float Value Accumulator updates.
FlowLayoutConcept.PrimaryDirection	Primary Direction	No	Yes	The direction along which the layout arranges items until the layout limit in that direction is reached.
FlowLayoutConcept.SecondaryDirection	Secondary Direction	No	Yes	The direction along which the flow layout arranges lines of the primary direction.
FocusManager.CyclicFocusNavigation	Cyclic Focus Navigation	No	Yes	Sets whether the focus chain navigation within the focus scope is cyclic. When you enable this property: - When the user navigates in the forward direction and the focus reaches the last focusable UI element of the focus scope, the focus navigation moves to the first focusable UI element. - When the user navigates in the backward direction and the focus reaches the first focusable UI element of the focus scope, the focus navigation moves to the last focusable UI element.
FocusManager.FocusOrder	Focus Order	No	Yes	Sets the focus chain order of the node within the focus scope.
FocusManager.FocusScopeType	Focus Scope Type	No	Yes	Sets the type of the focus scope node: - Group groups focusable nodes. - Fence keeps the focus chain navigation inside the scope and does not allow the focus chain navigation to enter or leave that scope. - Modal overlay blocks the key and touch input that originates outside of its boundaries and keeps the focus navigation within the scope boundaries. - Auto-Closing Modal overlay loses focus when key or touch input originates from a node that is outside of its node tree, and suppresses that input. - Modeless overlay propagates the key and touch input that originates outside of its boundaries to the nodes outside of its boundaries. - Auto-Closing Modeless overlay loses focus when key or touch input originates from a node that is outside of its boundaries, and propagates that input.
FocusManager.ScopeStateChangeMessageArguments.ReasonValue	Reason Value	No	No	The reason the modal or popup focus scope state is changed: - Force Focus specifies that the focus scope is explicitly brought to front or sent to back.
FontStyleConcept.CharacterSpacing	Character Spacing	No	Yes	Sets the character spacing in pixels.
FontStyleConcept.FixedCharacterWidth	Fixed Character Width	No	Yes	When set, overrides the font advance widths to make each character take a fixed amount of space specified in pixels.
FontStyleConcept.FontHintingPreference	Font Hinting Preference	No	Yes	Sets the hinting preference of the font. - No hinting: Render text without hinting the outlines of glyphs. - Native hinting: Prefer native hinter of the font over the auto-hinter of the rasterizer. - Auto hinting: Prefer auto-hinter of the rasterizer over the native hinter of the font.
FontStyleConcept.FractionalCharacterWidth	Fractional Character Width	No	Yes	Sets whether Kanzi uses fractional or rounded character widths to lay out text. In most cases fractional widths provide the best result. However, with small font sizes, fractional widths can cause the characters to run together or have too much space, making it difficult to read. - When enabled, Kanzi uses fractional character widths, which means that the spacing between characters varies and can be a fraction of a pixel. - When disabled, Kanzi uses character widths rounded to the nearest pixel. Disable fractional widths when you want to fix character spacing in whole-pixel increments and prevent characters in small font sizes from running together.
FontStyleConcept.LineSpacing	Line Spacing	No	Yes	Sets the line spacing in multiples of the normal line height of the selected FontStyleConcept.
FontStyleConcept.Size	Font Size	No	Yes	Sets the size of the font in pixels.
FontStyleConcept.SnapCharacterToPixelProperty	Snap Character To Pixel	No	Yes	Sets whether Kanzi positions characters in 2D rendering to the nearest pixel: - When enabled, text sharpness improves, but some characters can shift a fraction of a pixel. - When disabled, certain combinations of screen resolution, use of anti-aliasing, and font size can cause the text to appear blurry. In that case, you can improve the appearance of the text with the Fractional Character Width and Character Spacing properties.
FontStyleConcept.Style	Font Style	No	Yes	Sets the style of the FontStyleConcept.
FontStyleConcept.Weight	Font Weight	No	Yes	Sets the weight of the FontStyleConcept.
FrustumCullMargin	Frustum Cull Margin	No	Yes	The margin of the frustum cull radius of the node. For example, set the margin when a vertex shader modifies the geometry of the node. To use this property, enable the Frustum Culling property in the Draw Objects Render Pass you use to render the node.
GatherLightsRenderPass.OutputDirectionalLights	Output Directional Lights	No	Yes	Kanzi uses this property to allow binding to directional light set.
GatherLightsRenderPass.OutputPointLights	Output Point Lights	No	Yes	Kanzi uses this property to allow binding to point light set.
GatherLightsRenderPass.OutputSpotLights	Output Spot Lights	No	Yes	Kanzi uses this property to allow binding to spot light set.
GlobalAmbient	Global Ambient Color	No	Yes	The color that is multiplied automatically with the "Ambient" property of the materials in the scene.
GlossinessFactor	Glossiness Factor	No	Yes	Sets the glossiness of the material: 0 represents a rough, diffuse surface, and 1 represents a smooth, glossy surface.
GlossinessTexture	Glossiness Texture	No	Yes	Sets the texture that contains a glossiness map for the material. Kanzi reads the glossiness from the Alpha channel of this texture. Use the Glossiness Factor property to scale the glossiness from this texture.
GlyphTexture	Glyph Texture	No	Yes	The automatic texture of the glyph cache.
GridLayoutConcept.Column	Column	No	Yes	The column into which grid layout places the item.
GridLayoutConcept.ColumnDefinitions	Columns	No	Yes	Defines the number of columns in a grid layout and how the grid layout distributes the content in columns.
GridLayoutConcept.ColumnSpan	Column Span	No	Yes	Defines the number of columns an item in a grid layout occupies.
GridLayoutConcept.Direction	Layout Direction	No	Yes	The direction in which the items are arranged when you add them to a grid layout.
GridLayoutConcept.Row	Row	No	Yes	The row into which grid layout places the item.
GridLayoutConcept.RowDefinitions	Rows	No	Yes	Defines the number of rows in a grid layout and how the grid layout distributes the content in rows.
GridLayoutConcept.RowSpan	Row Span	No	Yes	Defines the number of rows an item in a grid layout occupies.
GridListBoxConcept.CalculatedOffset	Calculated Offset	No	Yes	Reports the current relative offset of an item in the Grid List Box in proportional range [0, 1].
GridListBoxConcept.CellHeight	Cell Height	No	Yes	Sets the height of each cell in the Grid List Box.
GridListBoxConcept.CellWidth	Cell Width	No	Yes	Sets the width of each cell in the Grid List Box.
GridListBoxConcept.Direction	Layout Direction	No	Yes	Sets the direction in which the Grid List Box arranges its items. When you change the layout direction you also change the scroll axis of the Grid List Box.
GridListBoxConcept.ItemAreaBegin	Item Area Begin	No	Yes	Sets the proportional offset where the area meant for the fully visible items in the Grid List Box starts. Kanzi uses the values of the Item Area Begin and Item Area End properties to calculate the value of the Node.VisibleAmountInParent property for each list item.You can use the VisibleAmountInParent property in shaders to fade out those list items that are not fully visible.
GridListBoxConcept.ItemAreaEnd	Item Area End	No	Yes	Sets the proportional offset where the area meant for the fully visible items in the Grid List Box ends. Kanzi uses the values of the Item Area Begin and Item Area End properties to calculate the value of the Node.VisibleAmountInParent property for each list item.You can use the VisibleAmountInParent property in shaders to fade out those list items that are not fully visible.
GridListBoxConcept.Scrolling	Scrolling	No	Yes	Reports whether the Grid List Box is currently scrolling.
GridListBoxConcept.ScrollPosition	Scroll Position	No	Yes	Sets the scroll position of the Grid List Box along the x and y axes as a relative position within the list box area. Use this property to move the list to a scroll position immediately, without scrolling. To update the scroll position with a binding, use a two-way or to-source binding.
GridListBoxConcept.ScrollSpeed	Scroll Speed	No	Yes	Reports the current scroll speed of the Grid List Box.
GridListBoxConcept.ScrollTargetPosition	Scroll Target Position	No	Yes	Reports the current target scroll value of the Grid List Box.
GridListBoxDraggingAccelerationCoefficient	Dragging Acceleration	No	Yes	Sets the acceleration of the Grid List Box when the user scrolls the Grid List Box by dragging the pointer. The higher the value, the quicker the Grid List Box reaches its final position. The default value is 80.
GridListBoxDraggingDragCoefficient	Dragging Drag	No	Yes	Sets the amount that drag affects the movement of the Grid List Box when the user scrolls the Grid List Box by dragging the pointer. The lower the value, the higher the drag and the quicker the scrolling stops. The default value is 150.
GridListBoxDraggingImpulseFactor	Dragging Impulse	No	Yes	Sets the amount of impulse to generate from the pointer movement when the user scrolls the Grid List Box by dragging the pointer.
GridListBoxMaximumNumberOfTouches	Maximum Number of Touches	No	Yes	Sets the maximum number of touch points allowed on the Grid List Box area for scrolling.
GridListBoxMinimumNumberOfTouches	Minimum Number of Touches	No	Yes	Sets the minimum number of touch points required on the Grid List Box area for scrolling.
GridListBoxRecognitionThreshold	Recognition Threshold	No	Yes	Sets the distance in pixels that the pointer has to move for the scrolling to start in the Grid List Box.
GridListBoxSensitivity	Scroll Sensitivity	No	Yes	Sets the amount that the scroll position changes relative to the movement of the pointer. The default value 1 makes the Grid List Box scroll the same amount as the user drags the pointer. For example, to set the Grid List Box to scroll twice the amount that the user drags the pointer, set the value of the property to 2.
GridListBoxSlidingAccelerationCoefficient	Sliding Acceleration	No	Yes	Sets the acceleration of the Grid List Box after the user releases the pointer with which they scroll the Grid List Box. The higher the value, the quicker the Grid List Box reaches the scroll target. The default value is 40.
GridListBoxSlidingDragCoefficient	Sliding Drag	No	Yes	Sets how much drag affects the movement of the Grid List Box after the user releases the pointer with which they scroll the Grid List Box. The lower the value, the higher the drag and the quicker the scrolling of the Grid List Box stops. The default value is 80.
GridListBoxSwipeDistance	Swipe Distance	No	Yes	Sets the distance that a swipe sends the scroll value in the Grid List Box, relative to the speed of the pointer.
Image2D.Image	Image	No	Yes	The image to display.
ImageClampPixelsValue	Clamp Pixels	No	Yes	Clamp the color channel maximum to the value. For SDR images the effective range is 0 to 1, and for HDR images any non-negative value. If one color channel needs to be clamped, then all other color channels are scaled down by the same ratio.
ImageFileNativePixelFormat	Native Pixel Format	No	Yes	Sets the native image format to use when exporting this image to the kzb file. Make sure that the graphics backend of your target device supports the format.
Input.MessageArgument.CapsLock	Caps Lock	No	No	Sets whether Caps Lock is on during the key event.
Input.MessageArgument.Key	Key	No	No	Sets the target logical key to handle.
Input.MessageArgument.KeyModifiers	Key Modifiers	No	No	Sets the target key modifiers to handle.
Input.MessageArgument.NavigationDirection	Navigation Direction	No	No	The navigation direction.
InputManipulator.InputMessageArguments.HitTestPoint	Hit Test Point	No	No
InputManipulator.InputMessageArguments.HitTestRayDirection	Hit Test Ray Direction	No	No
InputManipulator.InputMessageArguments.HitTestRayOrigin	Hit Test Ray Origin	No	No
InputManipulator.InputMessageArguments.ManipulatorPoint	Manipulator Point	No	No
InputManipulator.InputMessageArguments.ManipulatorRayDirection	Manipulator Ray Direction	No	No
InputManipulator.InputMessageArguments.ManipulatorRayOrigin	Manipulator Ray Origin	No	No
Instantiator3D.Node	Instantiated Node	No	No	Sets the node that this Instantiator node replicates.
IntValueAccumulator.IncrementSize	Increment Size	No	No	The size of the increments of this Int Value Accumulator.
IntValueAccumulator.IncrementSizeSource	Increment Size Source	No	No	The property type set on this node that determines the increment size of this Int Value Accumulator.
IntValueAccumulator.MaximumAccumulatedValue	Maximum Value	No	No	The maximum total accumulated integer value.
IntValueAccumulator.MinimumAccumulatedValue	Minimum Value	No	No	The minimum total accumulated integer value.
IntValueAccumulator.TargetPropertyType	Target Property Type	No	No	The property type on this node that this Int Value Accumulator updates.
IsAssetInAssetPackage	Export in Asset Package	No	Yes	When enabled, this item is exported into asset package if this project is saved as one.
IsDisabled	Disable KZB Export	No	Yes	Disables the exporting of the item into KZB. Can be used for, e.g. letting items out from certain profiles. The disabled items are always included in preview.
IsUsedByCode	Is Used by Code	No	Yes	Whether or not the application code uses this asset. Used for determining unused assets.
KeyManipulatorComponent.CapsLock	Caps Lock	No	Yes	Sets the Caps Lock value of the key manipulator. If the value is not set, Caps Lock state is ignored.
KeyManipulatorComponent.KeyModifier	Key Modifiers	No	Yes	Sets the key modifiers of the key manipulator. The default value is Undefined.
KeyManipulatorComponent.LogicalKey	Logical Key	No	No	Sets the logical key value of the key manipulator.
LegacyRenderPass.Color0FloatClearValue	Color Buffer 0 Clear Value (float)	No	Yes	Clear color value for signed integer color buffer 0
LegacyRenderPass.Color0IntegerClearValue	Color Buffer 0 Clear Value (integer)	No	Yes	Clear color value for integer color buffer 0
LegacyRenderPass.Color1ColorClearValue	Clear Color (Color Buffer 1)	No	Yes	The color used to clear the color buffer 1
LegacyRenderPass.Color1FloatClearValue	Color Buffer 1 Clear Value (float)	No	Yes	Clear color value for signed integer color buffer 1
LegacyRenderPass.Color1IntegerClearValue	Color Buffer 1 Clear Value (integer)	No	Yes	Clear color value for integer color buffer 1
LegacyRenderPass.Color2ColorClearValue	Clear Color (Color Buffer 2)	No	Yes	The color used to clear the color buffer 2
LegacyRenderPass.Color2FloatClearValue	Color Buffer 2 Clear Value (float)	No	Yes	Clear color value for signed integer color buffer 2
LegacyRenderPass.Color2IntegerClearValue	Color Buffer 2 Clear Value (integer)	No	Yes	Clear color value for integer color buffer 2
LegacyRenderPass.Color3ColorClearValue	Clear Color (Color Buffer 3)	No	Yes	The color used to clear the color buffer 3
LegacyRenderPass.Color3FloatClearValue	Color Buffer 3 Clear Value (float)	No	Yes	Clear color value for signed integer color buffer 3
LegacyRenderPass.Color3IntegerClearValue	Color Buffer 3 Clear Value (integer)	No	Yes	Clear color value for integer color buffer 3
LegacyRenderPass.ColorBufferClearColor	Clear Color (Color Buffer 0)	No	Yes	The color used to clear the color buffer 0
LegacyRenderPass.ColorBufferClearEnabled	Color Clear Enabled	No	No	Whether to clear the color buffer before writing the new color values.
LegacyRenderPass.ColorWriteMode	Color Write Mode	No	No	When set to None, writing to color buffer is disabled.
LegacyRenderPass.ComposerEnabled	Enabled	No	Yes	This determines if composer is rendered (enabled by default).
LegacyRenderPass.CullMode	Cull Mode	No	No	Sets the culling of the triangle faces in the rendered meshes of legacy render passes: - Back does not render the triangles whose normal points away from the camera. - Front does not render the triangles whose normal points towards the camera.
LegacyRenderPass.DepthBufferClearEnabled	Depth Clear Enabled	No	No	Sets whether to clear the depth buffer.
LegacyRenderPass.DepthBufferClearValue	Depth Clear Value	No	No	The value used for clearing the depth buffer.
LegacyRenderPass.DepthBufferTestEnabled	Depth Test Enabled	No	No	Whether to enable the depth test.
LegacyRenderPass.DepthBufferWriteEnabled	Depth Write Enabled	No	No	Sets whether to enable the writing of the depth buffer.
LegacyRenderPass.FlushAfterRender	Flush After Render	No	Yes	This determines if GPU pipeline is flushed after rendering of this composer has occurred, to prevent GPU pipeline stall.
LegacyRenderPass.FrustumCullingOn	Frustum Culling	No	No	Sets whether to use frustum culling. When frustum culling is enabled Kanzi does not render the objects that do not overlap with the viewing frustum of the camera.
LegacyRenderPass.RenderOnce	Render Once	No	No	Sets whether this render pass is rendered only once. When disabled this render passes renders every frame.
LegacyRenderPass.RenderPassCamera	Camera	No	No	The camera that is used for rendering this render pass. When set to "Scene Default Camera" Kanzi uses the default camera node from the active scene.
LegacyRenderPass.RenderPassMaterial	Override Material	No	No	The material that overrides all the materials in the objects that are rendered by this render pass. When set to "No Material" material overriding is not in use.
LegacyRenderPass.RenderPassObjectSource	Object Source	No	No	The object source for the render pass
LegacyRenderPass.RenderPassRenderTargetColor0	Render Target Color0	No	Yes	Sets where this render pass renders. You can set a render pass to render to screen or to a render target color0 attachment texture.
LegacyRenderPass.RenderPassRenderTargetColor1	Render Target Color1	No	Yes	Sets where this render pass renders. You can set a render pass to render to screen or to a render target color1 attachment texture.
LegacyRenderPass.RenderPassRenderTargetColor2	Render Target Color2	No	Yes	Sets where this render pass renders. You can set a render pass to render to screen or to a render target color2 attachment texture.
LegacyRenderPass.RenderPassRenderTargetColor3	Render Target Color3	No	Yes	Sets where this render pass renders. You can set a render pass to render to screen or to a render target color3 attachment texture.
LegacyRenderPass.RenderPassRenderTargetDepthStencil	Render Target Depth Stencil	No	Yes	Render Target Depth Stencil
LegacyRenderPass.RenderPassRenderTargetGenerateMipmap	Generate Mipmaps	No	No	Sets whether the render target texture generates mipmaps after the render pass.
LegacyRenderPass.RenderPassRenderTargetInvalidateAttachments	InvalidateAttachments	No	Yes	Which attachments, if any, should be invalidated after the render pass.
LegacyRenderPass.RenderPassRenderTargetMipmapLevel	Mipmap Level	No	No	Render Target Mipmap Level
LegacyRenderPass.RenderPassRenderTargetResolve	Resolve After	No	No	Sets whether the render target is multisample resolved after the render pass. When you want to apply multisampling, enable this property only in the last render pass.
LegacyRenderPass.RenderPassScissorEnabled	Scissor Enabled	No	No	Whether scissor area is enabled in render pass or not. When scissor area is enabled rendering is done only inside the specified scissor area.
LegacyRenderPass.RenderPassScissorType	Scissor Type	No	No	Whether the border settings of the scissor area are relative (range 0-1) or absolute (pixel coordinates).
LegacyRenderPass.StencilBufferClearEnabled	Stencil Clear Enabled	No	No	Sets whether to clear the stencil buffer.
LegacyRenderPass.StencilBufferClearValue	Stencil Clear Value	No	No	The value used for clearing the stencil buffer.
LegacyRenderPass.StencilBufferTestEnabled	Stencil Test Enabled	No	No	Whether or not the stencil test is enabled
LegacyRenderPass.StencilFailOperation	Stencil Fail Operation	No	No	Operation that is performed when the stencil test fails.
LegacyRenderPass.StencilFunction	Stencil Function	No	No	The function used to control whether a fragment is discarded by the stencil test.
LegacyRenderPass.StencilFunctionReferenceMask	Stencil Function Reference Mask	No	No	Specifies a mask in legacy render passes that is ANDed with both the reference value and the stored stencil value when the test is done
LegacyRenderPass.StencilFunctionReferenceValue	Stencil Function Reference Value	No	No	Specifies the reference value for the stencil test in legacy render passes.
LegacyRenderPass.StencilPassDepthFailOperation	Stencil Pass Depth Fail Operation	No	No	Operation that is performed when the stencil test fails and the depth test passes.
LegacyRenderPass.StencilPassDepthPassOperation	Stencil Pass Depth Pass Operation	No	No	Operation that is performed when both the stencil and depth test pass.
LegacyRenderPass.ViewportType	Viewport Type	No	No	When absolute, the viewport settings are read in pixel coordinates, when relative the settings are read as proportional values from top-left (0,0) corner to bottom-right (1,1) corner.
LevelOfDetail3D.MinimumArea	Minimum Area	No	Yes	When using #LodTypeScreenArea in the parent level of detail, use this property in the child of the level of detail to set the minimum screen area covered by the child in proportion to the screen size in range [0, 1].
LevelOfDetail3D.MinimumDistance	Minimum Distance	No	Yes	When using #LodTypeDistance in the parent level of detail, use this property in the child of the level of detail to set the minimum distance from the camera to the level of detail in range [0, Inf].
LevelOfDetail3D.Type	Type	No	No	Defines the type of the level of detail: - Distance sets the level of detail to use the minimum z distance from the camera to the level of detail. - Screen area sets the level of detail to use the minimum screen area covered by the child node in proportion to the screen size.
LightEnabled	Light Enabled	No	Yes	Whether the light is switched on or off. Only lights that are switched on affect rendering.
LightPropertyType	Light Type Name	No	Yes	The property type name of the light.
ListBoxConcept.ItemContainerGeneratorTypeName	Item Container Generator	No	Yes	Sets the name of the item container generator type to use to provide item containers dynamically for the List Box.
ListBoxConcept.ItemContainerTemplate	Item Container Template	No	Yes	Sets the List Box Item Container prefab that sets the appearance and behavior of the List Box items.
ListBoxConcept.ItemCount	Item Count	No	Yes	Reports the number of items in the List Box, including virtual items.
ListBoxConcept.ItemGeneratorTypeName	Item Generator	No	Yes	Sets the name of the item generator type to use to provide items dynamically to the List Box.
ListBoxConcept.ItemMessageArguments.ItemIndex	Item Index	No	No	Reports the index of the List Box item.
ListBoxConcept.ItemSelectedMessageArguments.PreviousSelectedItemIndex	Previous Selection	No	No	Reports the index of the previously selected List Box item. The value -1 indicates that no item was selected.
ListBoxConcept.ItemSelectedMessageArguments.SelectedItemIndex	Selection	No	No	Reports the index of the selected List Box item. The value -1 indicates that no item is selected.
ListBoxConcept.ItemTemplate	Item Template	No	Yes	Sets the prefab to use for the List Box items.
ListBoxConcept.KeepAliveItemCount	Keep Alive Item Count	No	Yes	Sets the size of the buffer for invisible List Box items. Kanzi returns to the Item Generator those invisible items that do not fit in the buffer.
ListBoxConcept.SelectedItemIndex	Selected Item Index	No	Yes	Sets the index of the item that is currently selected in the List Box node. A List Box node updates this property when the user scrolls that List Box node. By setting the value of this property to the index of the item that you want to select in a List Box, you can select that item.
ListBoxConcept.SelectionBehavior	Selection Behavior	No	Yes	Sets how the List Box behaves when the user selects an item. 'Bring to Center' sets the List Box to bring an item to the center of the List Box area when the user selects that item.
ListBoxItemContainer.ItemIndex	Item Index	No	Yes	Reports the index of the item in the List Box Item Container.
ListBoxItemContainer.Selected	Selected	No	Yes	Indicates whether the List Box item held by this List Box Item Container is selected. The List Box sets the value of this property.
ListBoxScrollingConcept.ScrollMessageArguments.ScrollPosition	Scroll Position	No	No	Reports the scroll position in the Scroll View within the List Box.
ListBoxScrollingConcept.ScrollMessageArguments.ScrollSpeed	Scroll Speed	No	No	Reports the scroll speed in the Scroll View within the List Box.
ListBoxScrollingConcept.UserScrollStartedMessageArguments.ItemIndex	Item Index	No	No	Reports the index of the List Box item where the user started scrolling.
LongPressManipulatorComponent.LongPressDuration	Long Press Duration	No	No	Sets the duration of the press required for the installed long-press manipulator to recognize the long-press gesture and to set off the Long Press trigger.
LookAt	Look At	No	Yes	Makes a node to always face the node set in this property.
MaskEffect2D.Channel	Mask Channel	No	Yes	Sets the texture channel to use as the input for the mask: - Alpha uses the alpha channel from the texture. This is the default. - Red uses the red color channel from the texture. - Green uses the green color channel from the texture. - Blue uses the blue color channel from the texture. - Luminance uses the luminance calculated from the red, green, and blue channels.
MaskEffect2D.Height	Mask Height	No	Yes	Sets the height of the mask to use in a layout. This value overrides the height of the texture that you use as the mask.
MaskEffect2D.HorizontalAlignment	Mask Horizontal Alignment	No	Yes	Sets the horizontal alignment of the mask effect: Left aligns the left edge of the mask with the left edge of the node. This is the default. Right aligns the right edge of the mask with the right edge of the node. Center aligns the mask horizontally to the center of the node. Stretch stretches the mask horizontally to fit the node from the left edge to the right edge.
MaskEffect2D.Invert	Invert Mask	No	Yes	Whether to invert the mask so that transparent areas become opaque and opaque areas become transparent.
MaskEffect2D.Mask	Mask Texture	No	Yes	Sets the mask texture. The default is no texture.
MaskEffect2D.Offset	Mask Offset	No	Yes	Sets the mask offset along the X and Y axes in pixels. Kanzi applies the mask offset after stretch, alignment, and scale.
MaskEffect2D.Scale	Mask Scale	No	Yes	Sets the factor by which to scale the mask. Kanzi applies the scale after stretch and alignment.
MaskEffect2D.ScreenSpace	Use Screen Space	No	Yes	Whether to layout the mask relative to the screen instead of the node.
MaskEffect2D.Strength	Mask Strength	No	Yes	Sets the strength of the mask effect in the range from 0 to 1: 0 disables the mask effect. 1 applies the mask at full strength. This is the default. Any value between 0 and 1 partially applies the mask as if the non-masked result was blended with the fully masked version.
MaskEffect2D.Stretch	Mask Stretch	No	Yes	Sets the stretch mode of the mask effect: None disables stretching. This is the default. Fill stretches the mask to fill the node. Uniform stretches the mask using uniform scaling to fill the node in either vertical or horizontal direction, whichever requires smaller scale. Uniform To Fill stretches the mask using uniform scaling to fill the node in either vertical or horizontal direction, whichever requires larger scale. Repeat does not stretch the mask, and allows the mask to repeat outside of its area based on the mask texture wrap mode.
MaskEffect2D.VerticalAlignment	Mask Vertical Alignment	No	Yes	Sets the vertical alignment of the mask effect: Bottom aligns the bottom edge of the mask with the bottom edge of the node. Top aligns the top edge of the mask with the top edge of the node. This is the default. Center aligns the mask vertically to the center of the node. Stretch stretches the mask vertically to fit the node from the top edge to the bottom edge.
MaskEffect2D.Width	Mask Width	No	Yes	Sets the width of the mask to use in a layout. This value overrides the width of the texture that you use as the mask.
MaskTexture	Mask Texture	No	Yes	The texture for masking other texture or color.
MaskTextureOffset	Mask Texture Offset	No	Yes	Sets an offset for mask in materials.
MaskTextureTiling	Mask Texture Tiling	No	Yes	Determines the number of times a mask is presented in a material
MaterialBrush.Material	Material	No	Yes	Material used when drawing with the brush
MaterialSetupRenderPass.Material	Material	No	Yes	Sets the material that will have all other Material Setup Render Pass properties set to.
MeshMorphTargetWeight	Weight	No	No	A weight value for a morph target
Message.IsRepeat	Is Repeat	No	No	Whether the key press is a repeat caused by the user holding down a keyboard key.
Message.ToggleState	Toggle State	No	No	Reports the toggle state of a Button.
MessageArgument.FloatValueAccumulator.SetAccumulatedValueBoundaries.MaximumAccumulatedValue	Maximum Value	No	No	Sets the maximum total accumulated float value.
MessageArgument.FloatValueAccumulator.SetAccumulatedValueBoundaries.MinimumAccumulatedValue	Minimum Value	No	No	Sets the minimum total accumulated float value.
MessageArgument.FocusReason	Focus Reason	No	No	Sets the focus reason: - Force Focus. Focus was forced on the node. - Focus Chain Navigation. Focus was moved as a result of navigation in the focus chain. - Node Hidden. The Visible property of the focused node was disabled.
MessageArgument.IntValueAccumulator.SetAccumulatedValueBoundaries.MaximumAccumulatedValue	Maximum Accumulated Value	No	No	Sets the maximum total accumulated integer value.
MessageArgument.IntValueAccumulator.SetAccumulatedValueBoundaries.MinimumAccumulatedValue	Minimum Accumulated Value	No	No	Sets the minimum total accumulated integer value.
MessageArgument.Key	Key	No	No	Sets the target logical key.
MessageArgument.Page.Navigate.Immediate	Immediate	No	No	Whether to navigate to the page instantly, without playing a transition animation.
MessageArgument.PropertyTargetEasingInterpolator.SetEnabled.Enabled	Enabled	No	No	Sets whether the Property Target Easing Interpolator attached to the Target Item interpolates the value of the Interpolated Property Type.
MessageArgument.Screen.ActivateThemeMessageArguments.Theme	Theme	No	No	Theme to activate
MessageArgument.ScrollView.ScrollDirection	Scroll Direction	No	No	Sets the scrolling direction for a Scroll View node.
MessageArgument.ScrollView.ScrollEdge	Scroll Edge	No	No	Set the direction in which a Scroll View node scrolls when you instruct it to scroll to either of the edges.
MessageArgument.ScrollView.ScrollPage	Scroll Page	No	No	Sets the direction in which a Scroll View node scrolls when you instruct it to scroll by the layout height of that Scroll View node.
MessageArgument.ScrollView.ScrollPosition	Position	No	No	Sets the x and y axis coordinates for the new scroll position of a Scroll View node.
MessageArgument.ScrollView.ScrollPositionX	Position X	No	No	Sets the x axis coordinate for the new scroll position of a Scroll View node.
MessageArgument.ScrollView.ScrollPositionY	Position Y	No	No	Sets the y axis coordinate for the new scroll position of a Scroll View node.
MessageArgument.ScrollView.ScrollSpeed	Speed	No	No	Sets the scrolling speed of a Scroll View node.
MessageArgument.ScrollView.ScrollTarget	Scroll Target	No	No	Sets the target position for a Scroll View node.
MessageArgument.ScrollView.SnapDirection	Snap Direction	No	No	Sets the direction of a snap request.
MessageArgument.ScrollView.SnapPosition	Snap Position	No	No	Sets the target of a snap request.
MessageArgument.ScrollView.Zoom	Zoom	No	No	Sets the zoom level for a Scroll View node.
MessageArgument.StateManager.EnteredState	State	No	No	State Manager State Entered
MessageArgument.StateManager.Immediate	Immediate	No	No	Whether to change the state instantly, without playing a transition animation.
MessageArgument.StateManager.LeftState	State	No	No	State Manager State Left
MessageArgument.StateManager.LoopStates	Loop State	No	No	Whether to go back to the first state after reaching the last state.
MessageArgument.StateManager.ShowStateManagerOnly	Show only items that have state manager	No	Yes	Show only items that have state manager
MessageArgument.StateManager.SourceState	Source State	No	No	Source State for the transition
MessageArgument.StateManager.State	State	No	No	State Manager State
MessageArgument.StateManager.StateDefinedInCode	State defined in code	No	Yes	State defined in code
MessageArgument.StateManager.StateGroup	State Group	No	No	The state group that contains the state to which you want to transition.
MessageArgument.StateManager.StateSelectorPlaceholder	State	No	Yes	Target state for dispatched message action
MessageArgument.StateManager.TargetState	Target State	No	No	Target State for the transition
MessageTrigger.MessageSource	Message Source	No	No	A filter that makes possible to intercept events only for a certain source node. Empty string intercepts messages from all sources.
MessageTrigger.RoutingMode	Routing Mode	No	No	The routing phase where the message is going to be intercepted.
MessageTrigger.SetHandled	Set Message Handled	No	No	When enabled the trigger intercepts the message, marks it as handled, and prevents further message delivery.
MetallicFactor	Metallic Factor	No	Yes	Sets the metalness of the material: 0 represents a non-metallic or dielectric object, and 1 represents a metallic object.
MetallicTexture	Metallic Texture	No	Yes	Sets the texture that contains a metallic map for the material. Kanzi reads the metalness from the Blue channel of this texture. Use the Metallic Factor property to scale the value from this texture.
Model3D.DrawnAsBoundingBox	Drawn as Bounding Box	No	Yes	When enabled the object is drawn its solid bounding box.
Model3D.Material	Material	No	Yes	Use this material to override the materials defined in the clusters of the mesh.
Model3D.Mesh	Mesh	No	No	The mesh resource used by the model.
MoveFocusAction.Direction	Direction	No	No	Direction to which the focus is transferred in the focus navigation chain.
MultiClickManipulatorComponent.ClickCount	Click Count	No	No	Sets the number of clicks or taps required for the installed multi-click manipulator to recognize the multi-click gesture and to set off the Multi-Click trigger. The default value is 2.
MultiClickManipulatorComponent.SendIntermediateClickMessages	Send Intermediate Click Messages	No	Yes	Sets whether to send Intermediate Click messages until the desired click count is reached.
MultiClickManipulatorComponent.Timeout	Multi-Click Timeout	No	No	Sets the time in milliseconds within which two consecutive clicks or taps must occur for the multi-click manipulator to continue recognizing them as the multi-click gesture. The default value is 250 ms.
NavigationManipulatorComponent.DownNavigationKey	Down Navigation Key	No	Yes	Sets the logical key value of the down navigation.
NavigationManipulatorComponent.DownNavigationKeyModifier	Down Navigation Key Modifier	No	Yes	Sets the key modifiers of the down navigation. The default value is Undefined.
NavigationManipulatorComponent.EndNavigationKey	End Navigation Key	No	Yes	Sets the logical key value of the end navigation.
NavigationManipulatorComponent.EndNavigationKeyModifier	End Navigation Key Modifier	No	Yes	Sets the key modifiers of the end navigation. The default value is Undefined.
NavigationManipulatorComponent.HomeNavigationKey	Home Navigation Key	No	Yes	Sets the logical key value of the home navigation.
NavigationManipulatorComponent.HomeNavigationKeyModifier	Home Navigation Key Modifier	No	Yes	Sets the key modifiers of the home navigation. The default value is Undefined.
NavigationManipulatorComponent.LeftNavigationKey	Left Navigation Key	No	Yes	Sets the logical key value of the left direction navigation.
NavigationManipulatorComponent.LeftNavigationKeyModifier	Left Navigation Key Modifier	No	Yes	Sets the key modifiers of the left direction navigation. The default value is Undefined.
NavigationManipulatorComponent.PageDownNavigationKey	Page Down Navigation Key	No	Yes	Sets the logical key value of the page-down navigation.
NavigationManipulatorComponent.PageDownNavigationKeyModifier	Page Down Navigation Key Modifier	No	Yes	Sets the key modifiers of the page-down navigation. The default value is Undefined.
NavigationManipulatorComponent.PageUpNavigationKey	Page Up Navigation Key	No	Yes	Sets the logical key value of the page-up navigation.
NavigationManipulatorComponent.PageUpNavigationKeyModifier	Page Up Navigation Key Modifier	No	Yes	Sets the key modifiers of the page-up navigation. The default value is Undefined.
NavigationManipulatorComponent.RightNavigationKey	Right Navigation Key	No	Yes	Sets the logical key value of the right direction navigation.
NavigationManipulatorComponent.RightNavigationKeyModifier	Right Navigation Key Modifier	No	Yes	Sets the key modifiers of the right direction navigation. The default value is Undefined.
NavigationManipulatorComponent.UpNavigationKey	Up Navigation Key	No	Yes	Sets the logical key value of the up navigation.
NavigationManipulatorComponent.UpNavigationKeyModifier	Up Navigation Key Modifier	No	Yes	Sets the key modifiers of the up navigation. The default value is Undefined.
NinePatchImage2D.ImageBottom	Bottom Image	No	Yes	The image to use in middle of the bottom row.
NinePatchImage2D.ImageBottomLeft	Bottom-Left Image	No	Yes	Image to use in the bottom-left corner.
NinePatchImage2D.ImageBottomRight	Bottom-Right Image	No	Yes	The image to use in the bottom-right corner.
NinePatchImage2D.ImageCenter	Center Image	No	Yes	The image to use in the center.
NinePatchImage2D.ImageLeft	Left Image	No	Yes	The image to use in the center-left.
NinePatchImage2D.ImageRight	Right Image	No	Yes	The image to use in the center-right.
NinePatchImage2D.ImageTop	Top Image	No	Yes	The image to use in the middle of the top row.
NinePatchImage2D.ImageTopLeft	Top-Left Image	No	Yes	The image to use in the top-left corner.
NinePatchImage2D.ImageTopRight	Top-Right Image	No	Yes	The image to use in the top-right corner.
NinePatchImage2D.StretchTypeBottom	Stretch Type Bottom	No	Yes	Control the display of the bottom image: - Stretch. Scale the image to fill the space between the bottom-left and bottom-right images. - Wrap. When the width of the space between the bottom-left and bottom-right images exceeds the width of the image, either extend the last column of pixels in the image or tile the image. Depends on the value of the texture's Wrap Mode property.
NinePatchImage2D.StretchTypeCenter	Stretch Type Center	No	Yes	Control the display of the center image: - Stretch. Scale the image to fill the width and height of the center of the nine patch image. - Wrap. When the height and width of the center exceed the size of the image, either extend the last row or column of pixels in the image or tile the image. Depends on the value of the texture's Wrap Mode property.
NinePatchImage2D.StretchTypeLeft	Stretch Type Left	No	Yes	Control the display of the left image: - Stretch. Scale the image to fill the space between the top-left and bottom-left images. - Wrap. When the height of the space between the top-left and bottom-left images exceeds the height of the image, either extend the last row of pixels in the image or tile the image. Depends on the value of the texture's Wrap Mode property.
NinePatchImage2D.StretchTypeRight	Stretch Type Right	No	Yes	Control the display of the right image: - Stretch. Scale the image to fill the space between the top-right and bottom-right images. - Wrap. When the height of the space between the top-right and bottom-right images exceeds the height of the image, either extend the last row of pixels in the image or tile the image. Depends on the value of the texture's Wrap Mode property.
NinePatchImage2D.StretchTypeTop	Stretch Type Top	No	Yes	Control the display of the top image: - Stretch. Scale the image to fill the space between the top-left and top-right images. - Wrap. When the width of the space between the top-left and top-right images exceeds the width of the image, either extend the last column of pixels in the image or tile the image. Depends on the value of the texture's Wrap Mode property.
Node.ActualDepth	Actual Layout Depth	No	Yes	The calculated size of the node in depth direction when used in a layout.
Node.ActualHeight	Actual Layout Height	No	Yes	The calculated height of the node when used in a layout.
Node.ActualWidth	Actual Layout Width	No	Yes	The calculated width of the node when used in a layout.
Node.ClipChildren	Clip Children	No	Yes	Sets whether to clip the child nodes of thos node. Kanzi clips the child nodes whose bounding box is completely outside of the bounding box of their parent node. Use this property with layout nodes. The child nodes can use only translation transformation.
Node.ContentStretch	Content Stretch	No	Yes	Sets how the content that belongs to this node is stretched (as opposed to manipulating the actual node size).
Node.Depth	Layout Depth	No	Yes	The size of the node in depth direction when used in a layout. Overrides the default bounds of the item.
Node.DepthAlignment	Depth Alignment	No	Yes	The alignment in depth direction the node should use when it resides under a layout.
Node.DepthMargin	Depth Margin	No	Yes	Sets the depth distance between this node and other nodes that are adjacent to this node in a layout. To set the Depth Margin property fields in a binding use: - Vector_X to access the Back property field - Vector_Y to access the Front property field
Node.EffectivelyEnabled	Effectively Enabled	No	Yes	Indicates whether this node and its ancestor nodes are enabled. Use this property in state managers and bindings to observe whether a node is effectively enabled. To enable or disable a node, use the Enabled property. When a node is effectively disabled: - When that node is focused, it receives keyboard input until the focus moves to another node. - When that node is not focused, it is not part of the focus chain and does not receive keyboard input.
Node.Enabled	Enabled	No	Yes	Whether this node is enabled. When you disable this property in a node, that node and its descendant nodes in the same overlay focus scope are effectively disabled. Effectively disabling a node removes that node from the focus chain and cancels all the active input manipulators.Use the Effectively Enabled property to observe whether a node is effectively enabled.
Node.Focusable	Focusable	No	Yes	Indicates whether the node can receive focus.
Node.Focused	Focused	No	Yes	Indicates whether the node has keyboard focus.
Node.FocusState	Focus State	No	Yes	Reports the focus state of a node: - No focus (0) indicates that the node is not focused. For a focus scope node indicates that none of the nodes in the scope have focus. - Logical focus (1) indicates that the node is the logical focus node of an overlay-type focus scope. For a focus scope node indicates that one of the nodes in that scope is the logical focus node. - Keyboard focus (2) indicates that the node is the keyboard focus node of the application and receives keyboard input. For a focus scope node indicates that one of the nodes in that scope is the keyboard focus node. Use this property in state managers and bindings to implement focus states in the UI nodes. To observe whether a node is the keyboard focus node, you can use the boolean Focus > Focused property.
Node.FontFamily	Font Family	No	Yes	The font family used to render the text.
Node.Height	Layout Height	No	Yes	The height of the node when used in a layout. Overrides the default bounds of the item.
Node.HitTestable	Hit Testable	No	Yes	When enabled, users can pick the node from the default Camera node of the active Scene node. For example, you must enable hit testing for Button nodes to work.
Node.HitTestableContainer	Hit Testable Container	No	Yes	When enabled, Kanzi uses the layout bounds as geometry for hit testing.
Node.HorizontalAlignment	Horizontal Alignment	No	Yes	The alignment in horizontal direction the node should use when it resides under a layout.
Node.HorizontalMargin	Horizontal Margin	No	Yes	Sets the horizontal space between this node and other nodes that are adjacent to this node in a layout. To set the Horizontal Margin property fields in a binding use: - Vector_X to access the Left property field - Vector_Y to access the Right property field
Node.Hover	Hover	No	Yes	Indicates whether a node is the foremost hit testable node under the cursor.
Node.Locale	Locale	No	No	The locale of the node.
Node.Opacity	Opacity	No	Yes	Opacity of the node.
Node.Path	Node.Path	No	Yes	Full path to the node.
Node.Projection2DTo3DScale	2D to 3D Projection Scale	No	Yes	Sets the scale factor to project pixels to 3D size. When scale is 1, then the size of one pixel is one 3D space unit.
Node.StateManager	State Manager	No	Yes	Sets the State Manager to the node.
Node.Style	Style	No	Yes	Sets a style to the node.
Node.VerticalAlignment	Vertical Alignment	No	Yes	The alignment in vertical direction the node should use when it resides under a layout.
Node.VerticalMargin	Vertical Margin	No	Yes	Sets the vertical space between this node and other nodes that are adjacent to this node in a layout. To set the Vertical Margin property fields in a binding use: - Vector_X to access the Bottom property field - Vector_Y to access the Top property field
Node.Visible	Visible	No	Yes	When disabled, Kanzi does not render the node.
Node.VisibleAmountInParent	Visible Amount in Parent	No	Yes	Sets the amount the node is inside its parent. Use the value of this property in shaders to implement fades. Calculated by the parent node.
Node.Width	Layout Width	No	Yes	The width of the node when used in a layout. Overrides the default bounds of the item.
Node2D.AspectRatio	Aspect Ratio	No	Yes	Determines the proportion of width and height. You cannot set both the Aspect Ratio and both, Width and Height.
Node2D.BackgroundBrush	Background Brush	No	Yes	The background brush to paint the background of 2D nodes.
Node2D.CacheValid	Cache Valid	No	Yes	Indicates whether the node is cached. To disable the cache for one frame, disable this property.
Node2D.CachingMode	Caching Mode	No	Yes	Sets the caching mode of this node: - Disabled sets Kanzi to render the node and its descendants normally, without caching. This is the default. - Enabled sets Kanzi to cache the node and its descendants and render the node from the cache image until you invalidate the cache by disabling the Cache Valid property. - Automatic sets Kanzi to automatically update the cache of the node whenever the content of the node or its descendants change.
Node2D.CompositionBrush	Composition Brush	No	Yes	The brush to use to compose 2D nodes to screen.
Node2D.DisableRenderTargetClear	Disable Render Target Clear Color	No	Yes	Do not clear render target buffers before rendering into it even if necessary.
Node2D.Effect	Effect	No	Yes	Reports the runtime effect instance that this node uses. Kanzi sets the value of this property internally when the value of the Effect Prefab property in this node changes.
Node2D.EffectPrefab	Effect Prefab	No	Yes	The 2D Effect to use for this node.
Node2D.ForceComposition	Force Composition	No	Yes	Force rendering to composing target even if not otherwise necessary.
Node2D.ForegroundBrush	Foreground Brush	No	Yes	The foreground brush to paint the foreground of 2D nodes.
Node2D.ForegroundHint	Foreground Hint	No	Yes	Give a hint of the type of the foreground of 2D nodes: - None renders the background brush after rendering the node. - Translucent renders the background brush before the content of the node. - Occluding renders the background brush.
Node2D.LayoutTransformation	Layout Transformation	No	Yes	The 2D transformation to be applied before layouting.
Node2D.OffscreenRendering	Off-Screen Rendering	No	Yes	When set and the node has an explicitly set render target, do not render the resulting framebuffer to screen.
Node2D.PerspectiveTransformation	Perspective Transformation	No	Yes	The 3D transformation to be applied after layouting.
Node2D.PerspectiveTransformationFov	Perspective Transformation FOV	No	Yes	The 3D transformation field of view (degrees) to be applied after layouting.
Node2D.PerspectiveTransformationMode	Perspective Transformation Mode	No	Yes	Defines the mode of operation for the coordinate system and field of view.
Node2D.PerspectiveTransformationOrigin	Perspective Transformation Origin	No	Yes	The 3D transformation origin to be used for perspective transformation on this or child nodes.
Node2D.PerspectiveTransformationPivot	Perspective Transformation Pivot	No	Yes	The 3D pivot point in relative coordinates.
Node2D.PixelFormat	Pixel Format	No	Yes	The pixel format of the node if rendering to a texture.
Node2D.RenderSelf	Render Self	No	Yes	Whether the node renders itself. Does not affect the rendering of child nodes.
Node2D.RenderTarget	Render Target	No	Yes	Forces the node to be rendered into a given render target texture. When set to "No Target", regular conditions whether node is rendered to a texture, such as opacity and rotation, are applied.
Node2D.RenderTargetMinimumHeight	Render Target Minimum Height	No	Yes	Sets the minimum height of implicitly generated render targets.
Node2D.RenderTargetMinimumWidth	Render Target Minimum Width	No	Yes	Sets the minimum width of implicitly generated render targets.
Node2D.RenderTargetReallocationLimit	Render Target Reallocation Limit	No	Yes	The change in size that triggers reallocation of a render target.
Node2D.RenderTransformation	Render Transformation	No	Yes	The 2D transformation to be applied after layouting.
Node2D.RenderTransformationOrigin	Render Transformation Origin	No	Yes	Sets the render transform origin in relative coordinates.
Node2D.SnapToPixel	Snap to Pixel	No	Yes	Snap the translation of the node and its size into pixel boundary.
Node3D.FinalTransformation	Final Transformation	No	Yes	The combined location, orientation and scale of the node and its ancestor nodes. Automatically calculated by the system.
Node3D.LayoutTransformation	Layout Transformation	No	Yes	The location, orientation and scale of the node relative to its parent node. Layout Transformation affects the layout. If you do not want to affect the layout, use Render Transformation.
Node3D.RenderTransformation	Render Transformation	No	Yes	The location, orientation, and scale of the node relative to its parent node. Render transformation does not affect the layout of the node.
NodeComponent.NodeComponentMessageArguments.TargetName	Target Node Component Name	No	No	Sets the name of the node component that receives this message. To send this message to every node component in this node, use an empty string.
NodeComponent.NodeComponentSourceMessageArguments.SourceName	Source Node Component Name	No	No	Name of the node component that sent the message.
NodeListRenderPass.Filter	Filter	No	Yes	Sets the filter that the Node List Render Pass uses to filter or sort a list of incoming nodes.
NodeListRenderPass.NodeList	Node List	No	Yes	Input node list range. Set by a binding from nearest parent node list.
NodeListRenderPass.OutputNodeList	Output Node List	No	Yes	Output node list range. Set by Node List Render Pass as result of filtering the Input Node List.
NormalScale	Normal Scale	No	Yes	Sets the normal scale for the material. Use the scale to set the intensity of the Normal Texture.
NormalTexture	Normal Texture	No	Yes	Sets the texture that contains a normal map for the material. Use the Normal Scale property to scale the texture value.
OcclusionStrength	Occlusion Strength	No	Yes	Sets the occlusion strength for the material. Use the strength to set the intensity of the Occlusion Texture.
OcclusionTexture	Occlusion Texture	No	Yes	Sets the texture that contains an occlusion map for the material. Use the Occlusion Strength property to scale the occlusion from the texture.
OnPropertyChangedTrigger.IgnoreIdenticalValue	Ignore Identical Value	No	No	Invoke the trigger only on change in the monitored property's value.
OnPropertyChangedTrigger.SourceNode	Node	No	No	The node for which this trigger monitors property changes.
OnPropertyChangedTrigger.SourcePropertyType	Property Type	No	No	The property type the changes of which trigger this trigger.
Page.AutoActivate	Keep Active	No	No	Always activate this Page node when its parent is active.
Page.RotationOffset	Rotation Offset	No	Yes	The angle in degrees by which to rotate a Page node.
Page.ScaleOffset	Scale Offset	No	Yes	The factor by which to scale a Page node.
Page.SlideOffset	Slide Offset	No	Yes	The offset to slide a Page node in horizontal or vertical direction:nX [-1, 1] to move the Page node horizontallynY [-1, 1] to move the Page node vertically
Page.State	Activation State	No	Yes	The state of this Page node: false (inactive and invisible) or true (active and visible) (read-only).
Page.TransitionPhase	Transition Phase	No	Yes	The phase of the transition. For example, use for pixel-based effects.
PageHost.DefaultSubPage	Default Subpage	No	No	The default or the currently active subpage, which Kanzi automatically activates whenever this PageHost node becomes active.
PageHost.LoopSubPages	Loop Subpages	No	No	Loop the subpages when navigating to the next or previous subpage.
PageHost.Transitions	Transitions	No	Yes	Transitions to be used within this PageHost node.
PageTransition.Direction	Direction	No	No	Defines whether the transition is unidirectional (one way) or bidirectional (two way).
PageTransition.Duration	Duration	No	No	The duration of a Page node transition (in milliseconds).
PageTransition.From	From	No	No	The selection criteria for the source Page node. Use * for any Page node.
PageTransition.To	To	No	No	The selection criteria for the target Page node. Use * for any Page node.
PageTransitionAnimation.AnimationTarget	Animation Target	No	No	Defines the animation target, either page transitioning in or page transitioning out.
PageTransitionAnimation.EndValue	End Value	No	No	The ending value for the animation.
PageTransitionAnimation.PropertyType	Transition Property	No	No	Defines which property to animate.
PageTransitionAnimation.StartValue	Start Value	No	No	The starting value for the animation.
PanManipulator.PanDelta	Pan Delta	No	No	Holds the change in pan position since the last update in global screen coordinates.
PanManipulator.PanVelocity	Pan Velocity	No	No	Holds the current estimate of the pan velocity in global screen coordinates.
PanManipulatorComponent.MaximumTouchPoints	Maximum Touch Points	No	Yes	Sets the maximum number of touches allowed on the node area for the installed pan manipulator to recognize the pan gesture and to set off the Pan Started trigger. The default value is 10. The value cannot be lower than the value of the Minimum Touch Points property.
PanManipulatorComponent.MinimumTouchPoints	Minimum Touch Points	No	Yes	Sets the minimum number of touches required on the node area for the installed pan manipulator to recognize the pan gesture and to set off the Pan Started trigger. The default value is 1.
PanManipulatorComponent.RecognitionThreshold	Recognition Threshold	No	Yes	Sets the threshold in pixels on the horizontal and vertical axis that the finger must move before Kanzi recognizes it as a pan gesture. The default value is 5 pixels on both axes. To disable the pan gesture along either axis, set the threshold on that axis to -1.
PanManipulatorComponent.RoutingMode	Routing Mode	No	No	Routing mode determines when the input manipulator recognizes input events: - Bubbling: The installed manipulator recognizes input events that are traversing from the hit test node or the focus node to the root node. - Tunneling: The installed manipulator recognizes input events that are traversing from the root node to the hit test node or to the focus node.
ParallelActivityHostConcept.BringActivatedToFront	Bring Activated Activity To Front	No	Yes	Sets whether to show the activated Activity in front within its Parallel Activity Host. This property affects the z-order of the activated Activity within the same Activity priority layer: - When enabled, the Activity is shown in front. - When disabled, the z-order of the activated child Activity is determined by the order in which you added that Activity to the parent Parallel Activity Host. This is the default behavior.
PinchManipulator.PinchPositionDelta	Pinch Position Delta	No	No
PinchManipulator.PinchRotation	Pinch Rotation	No	No
PinchManipulator.PinchScale	Pinch Scale	No	No
PipelineStateRenderPass.BlendMode	Blend Mode	No	Yes	Overrides the blend mode set in each node that this render pass renders.
PipelineStateRenderPass.ColorWriteMode	Color Write Mode	No	Yes	Sets which channels the render pass writes to the color buffer. To disable the color write, set the property to None.
PipelineStateRenderPass.CullMode	Cull Mode	No	Yes	Sets the culling of the triangle faces in the rendered meshes. Set to: - Back to render the triangles whose normal points towards a Camera node - Front to render the triangles whose normal points away from a Camera node
PipelineStateRenderPass.DepthTestFunction	Depth Test Function	No	Yes	Controls whether the depth test discards a fragment.
PipelineStateRenderPass.DepthWriteEnabled	Depth Write Enabled	No	Yes	Sets whether the render pass writes to the depth buffer.
PipelineStateRenderPass.Scissor	Scissor Area	No	Yes	Sets the scissor test within the current rendering Viewport node. You can define the scissor in either relative or absolute coordinates, the default is relative. Use the Scissor Mode property to set the coordinate type.
PipelineStateRenderPass.ScissorMode	Scissor Mode	No	Yes	Sets the scissor test coordinate mode.
PipelineStateRenderPass.StencilFailOperation	Stencil Fail Operation	No	Yes	Sets the operation that the render pass performs when the stencil test fails.
PipelineStateRenderPass.StencilMask	Stencil Function Mask	No	Yes	Sets a mask on which the AND operation is executed with both the reference value and the stored stencil value when the test is done.
PipelineStateRenderPass.StencilPassDepthFailOperation	Stencil Pass Depth Fail Operation	No	Yes	Sets the operation that the render pass performs when the stencil test passes, but the depth test fails.
PipelineStateRenderPass.StencilPassDepthPassOperation	Stencil Pass Depth Pass Operation	No	Yes	Sets the operation that the render pass performs when both, the stencil and the depth test, pass.
PipelineStateRenderPass.StencilReferenceValue	Stencil Function Reference Value	No	Yes	Sets the reference value for the stencil test.
PipelineStateRenderPass.StencilTestFunction	Stencil Test Function	No	Yes	Controls whether the stencil test discards a fragment.
PipelineStateRenderPass.StencilWriteEnabled	Stencil Write Enabled	No	Yes	Sets whether to enable writing to the stencil buffer.
PipelineStateRenderPass.Viewport	Viewport Area	No	Yes	Modifies the current rendering Viewport node. You can define the Viewport in either relative or absolute coordinates, the default is relative. Use the Viewport Mode property to set the coordinate type.
PipelineStateRenderPass.ViewportMode	Viewport Mode	No	Yes	Sets the coordinate type for the Viewport node.
PointLight	Point Light	No	Yes	Point light settings
PointLightAttenuation	Point Light Attenuation	No	Yes	Sets the effect that this Point Light has on nodes that are farther away. Distance of light from the lighted surface is input in a quadratic function, the 3 components are the constant, linear and quadratic coefficients for the distance variable.
PointLightColor	Point Light Color	No	Yes	Sets the color of the Point Light.
PointLightRadius	Point Light Radius	No	Yes	Sets the distance at which the intensity of the Point Light reaches zero. For infinite distance, set the property value to 0.
PrefabViewConcept.AsynchronousLoadCompletedMessageArguments.PrefabTemplate	Prefab Template	No	No	The prefab whose resources finished loading asynchronously.
PrefabViewConcept.LoadAsynchronouslyMessageArguments.PrefabTemplate	Prefab Template	No	No	The prefab whose resources you want to load asynchronously.
PrefabViewConcept.Prefab	Prefab Template	No	Yes	Node to use on this prefab view.
ProgressiveRenderingViewport2D.Animation	Timeline	No	Yes	The animation timeline to play in Progressive Rendering Viewport 2D
ProgressiveRenderingViewport2D.MultisampleLevel	Multisample Level	No	Yes	Sets the multisampling level of the progressive rendering backbuffers. To disable multisampling, remove the property or set the property value to 1.
ProjectResourceDefaultCrossProjectVisibility	Resource Visibility Across Projects	No	Yes	Sets whether the resources of this project are available to referencing projects: - Private makes the resources available only to this project. This is the default value. - Public makes the resources available in the dropdown menus of referencing projects. To override this setting for an individual resource, add and set the Visibility Across Projects property for that resource.
PropertyDrivenAnimationPlayer.Enabled	Enabled	No	No	Specifies whether animation timeline is applied.
PropertyDrivenAnimationPlayer.RelativePlayback	Relative Playback	No	No	Specifies whether animations are applied in relative manner by adding animated value to target property value instead of replacing the property value.
PropertyDrivenAnimationPlayer.Timeline	Target Animation Timeline	No	No	The target animation timeline for property driven animation.
PropertyDrivenAnimationPlayer.TimePropertyTypeProperty	Time Controller Property Type	No	No	The type of property on the node whose value is taken by the player as input time for timeline playback.
PropertyTargetEasingInterpolator.EasingFunction	Easing Function	No	No	Sets the easing function that defines the curve of the interpolation.
PropertyTargetEasingInterpolator.EasingMode	Easing Mode	No	No	Sets how to apply the easing function to the interpolation.
PropertyTargetEasingInterpolator.Enabled	Enabled	No	Yes	Sets whether the Property Target Easing Interpolator interpolates the value of the Interpolated Property Type.
PropertyTargetEasingInterpolator.InterpolatedPropertyField	Interpolated Field	No	No	The property field of the Interpolated Property Type you want to interpolate from its previous value to a new value using this Property Target Easing Interpolator.
PropertyTargetEasingInterpolator.InterpolatedPropertyType	Interpolated Property Type	No	No	The property type you want to interpolate from its previous value to a new value using this Property Target Easing Interpolator.
PropertyTargetEasingInterpolator.InterpolationDuration	Interpolation Duration	No	No	Sets the duration of the interpolation in milliseconds.
PropertyTargetEasingInterpolator.InterpolationIfInterrupted	Interpolation If Interrupted	No	No	Sets what happens if a new value is set to the interpolated property before interpolation to its previous value completes: Start from current interpolated value uses the current value of the ongoing interpolation as the start value of the new interpolation. Start from current target value uses the target value of the ongoing interpolation as the start value of the new interpolation.
PropertyTargetEasingInterpolator.NotifyInterpolationCompleted	Notify Interpolation Completed	No	Yes	Sets whether the Property Target Easing Interpolator dispatches a Completed message every time it completes interpolation.
PropertyTargetInterpolator.Acceleration	Acceleration	No	No	Acceleration coefficient of property interpolation. Larger acceleration leads to faster reaching new property value.
PropertyTargetInterpolator.Drag	Drag	No	No	Drag coefficient of property interpolation. Larger drag lowers maximum speed of interpolation.
PropertyTargetInterpolator.InterpolatedPropertyField	Interpolated Field	No	No	The field of a property on a node which is interpolated from its previous value to new one by property target interpolator.
PropertyTargetInterpolator.InterpolatedPropertyType	Interpolated Property Type	No	No	The property type of a property on a node which is interpolated from its previous value to new one by property target interpolator.
RangeConcept.CommonMessageArguments.Value	Range Value	No	No	Range Value
RangeConcept.IsValueChanging	Is Value Changing	No	Yes	Whether the value is currently changing.
RangeConcept.MaximumValue	Maximum Value	No	Yes	The maximum value that the range allows.
RangeConcept.MinimumValue	Minimum Value	No	Yes	The minimum value that the range allows.
RangeConcept.NormalizedValue	Normalized Value	No	Yes	The current value normalized to range [0, 1].
RangeConcept.Step	Step Value	No	Yes	The minimum amount that the value of the range can change at a time.
RangeConcept.Value	Value	No	Yes	The current value.
RenderPass.Camera	Camera	No	Yes	Sets the Camera node that you want to use to render the nodes. To use the default Camera node in that Scene node, do not set the value for this property.
RenderPass.Enabled	Enabled	No	Yes	Whether Kanzi executes this render pass and its child render pass tree.
RenderPass.InputViewportArea	Input Viewport Area	No	Yes	Reports the viewport area relative to the composition space as passed from the parent render pass. To access the Input Viewport Area property fields in a binding, use: - X for the offset along the x axis relative to the composition space - Y for the offset along the y axis relative to the composition space - Z for the width of the viewport - W for the height of the viewport
RenderPassView.RenderPassPrefab	Render Pass Prefab	No	Yes	Sets the Render Pass Prefab that this Render Pass View instantiates.
ResourceCrossProjectVisibility	Visibility Across Projects	No	Yes	Sets whether this resource is available to referencing projects: - Project setting uses the value of the Resource Visibility Across Projects property of the project. - Private makes the resource available only to this project. - Public makes the resource available in the dropdown menus of referencing projects.
ResourceDictionarySelector.SelectedDictionary	Selected Theme	No	No	The currently selected theme in the theme group. In Kanzi Studio you can change the current theme with the ActivateTheme action.
ResourceKeepAliveBehavior	Keep Alive Behavior	No	Yes	The keep-alive behavior of this resource. Can be used to deny unloading of the resource.
RoughnessFactor	Roughness Factor	No	Yes	Sets the roughness of the material: 0 represents a smooth, glossy surface, and 1 represents a rough, diffuse surface.
RoughnessTexture	Roughness Texture	No	Yes	Sets the texture that contains a roughness map for the material. Kanzi reads the roughness from the Green channel of the texture. Use the Roughness Factor property to scale the roughness from this texture.
Scene.Camera	Camera	No	Yes	The camera for displaying the scene.
Scene.HitTestCamera	Hit Testing Camera	No	Yes	The camera used in hit testing the objects in the scene. When not set, the default camera is used.
Screen.ClearColor	Screen Clear Color	No	Yes	If screen has a clear color, screen will be cleared with the specified color before all other rendering. Depth will be cleared to 1.0f and stencil will be cleared to 0.
Screen.HostName	Host Name	No	Yes	Containes the name of the host the node originates from.
ScrollViewConcept.AllowedScrollAxis	Allowed Scroll Axis	No	Yes	Sets the axis on which you want to allow this Scroll View node to scroll.
ScrollViewConcept.DraggingAccelerationCoefficient	Dragging Acceleration	No	Yes	Sets the acceleration of the node controlled by a Scroll View node while you drag that Scroll View node. Use low values when you want that node to slowly reach the final position. Use high values when you want that node to quickly reach the final position.
ScrollViewConcept.DraggingDragCoefficient	Dragging Drag	No	Yes	Sets the amount that drag affects the movement of the node controlled by a Scroll View node while you drag that Scroll View node. The lower the value the higher the drag and the faster the sliding of that node stops.
ScrollViewConcept.DraggingImpulseFactor	Dragging Impulse	No	Yes	Sets the amount of impulse generated from the pointing device movement when dragging a Scroll View node.
ScrollViewConcept.LoopingXEnabled	Looping X Enabled	No	Yes	Sets the node controlled by a Scroll View node to start scrolling from the beginning when the scroll reaches the scroll bounds on the x axis. When the scroll value reaches the maximum value of the bound, the value changes to the minimum value and the other way around. Use the Scroll Bounds Minimum and Scroll Bounds Maximum properties to set the scroll bounds.
ScrollViewConcept.LoopingYEnabled	Looping Y Enabled	No	Yes	Sets the node controlled by a Scroll View node to start scrolling from the beginning when the scroll reaches the scroll bounds on the y axis. When the scroll value reaches the maximum value of the bound, the value changes to the minimum value and the other way around. Use the Scroll Bounds Minimum and Scroll Bounds Maximum properties to set the scroll bounds.
ScrollViewConcept.MaximumNumberOfTouches	Maximum Number of Touches	No	Yes	Sets the maximum number of touch points allowed for a Scroll View pan.
ScrollViewConcept.MinimumNumberOfTouches	Minimum Number of Touches	No	Yes	Sets the required number of touch points pressed for a Scroll View node pan to start. Scroll View nodes with minimum number of touches greater than one precede the children in touch processing.
ScrollViewConcept.RecognitionThreshold	Recognition Threshold	No	Yes	Sets the amount a pointing device must move for the scrolling to start on a Scroll View node.
ScrollViewConcept.ScrollBoundsMaximum	Scroll Bounds Maximum	No	Yes	Sets the coordinates of the bottom-right corner of the scroll bounds rectangle. Scroll bounds define where the scrolling begins and ends.
ScrollViewConcept.ScrollBoundsMinimum	Scroll Bounds Minimum	No	Yes	Sets the coordinates of the top-left corner of the scroll bounds rectangle. Scroll bounds define where the scrolling begins and ends.
ScrollViewConcept.Scrolling	Scrolling	No	Yes	Whether a Scroll View node is currently scrolling (read-only).
ScrollViewConcept.ScrollPosition	Scroll Position	No	Yes	Sets the scroll position of the Scroll View along the x and y axes as a relative position within the scroll view area. Use this property to set the scroll position immediately, without scrolling. To update the scroll position with a binding, use a two-way or to-source binding.
ScrollViewConcept.ScrollSpeed	Scroll Speed	No	Yes	The current scroll speed (read-only).
ScrollViewConcept.ScrollTargetPosition	Scroll Target Position	No	Yes	The current target scroll value (read-only).
ScrollViewConcept.Sensitivity	Scroll Sensitivity	No	Yes	Sets the amount the position changes relative to the movement of the pointer that starts the swiping. The higher the value the more the position of the node controlled by a Scroll View node changes. The default value is 1.
ScrollViewConcept.SlidingAccelerationCoefficient	Sliding Acceleration	No	Yes	Sets the acceleration of the node controlled by a Scroll View node after you release the pointer with which you swipe. Use low values when you want that node to slowly reach the final position. Use high values when you want that node to quickly reach the final position.
ScrollViewConcept.SlidingDragCoefficient	Sliding Drag	No	Yes	Sets the amount that drag affects the movement of the node controlled by a Scroll View node after you release the pointer with which you swipe. The lower the value the higher the drag and the faster the sliding of the object controlled by the Scroll View node stops.
ScrollViewConcept.StepMultiplier	Step Multiplier	No	Yes	Sets the smallest distance that a Scroll View scrolls.
ScrollViewConcept.SwipeDistance	Swipe Distance	No	Yes	Sets the distance that a swipe sends the scroll value, relative to the pointing device speed.
ScrollViewConcept.Zoom	Zoom	No	Yes	Sets the current zoom level.
ScrollViewConcept.ZoomAffectsScrolling	Zoom Affects Scrolling	No	Yes	Controls whether the scroll position is scaled, according to the zoom level.
ScrollViewConcept.ZoomEnabled	Zoom Enabled	No	Yes	Sets whether to install a pinch manipulator that generates zoom messages.
ScrollViewConcept.ZoomMaximum	Maximum Zoom	No	Yes	Sets the maximum zoom level.
ScrollViewConcept.ZoomMinimum	Minimum Zoom	No	Yes	Sets the minimum zoom level.
ShadowEffect2D.Angle	Shadow Angle	No	Yes	Sets the direction of the shadow as an angle relative to the positive x axis. The default is 45 degrees.
ShadowEffect2D.BlurRadius	Shadow Blur Radius	No	Yes	Sets the softness of the shadow by defining the distance in pixels the shadow blur extends outward from an edge. For a shadow with sharp edges, set to 0. The default is 8 pixels.
ShadowEffect2D.Color	Shadow Color	No	Yes	Sets the color and alpha of the shadow.
ShadowEffect2D.Distance	Shadow Distance	No	Yes	Sets how far to move the shadow from the object in the direction set by the Shadow Angle property. The default is 10 pixels.
ShadowEffect2D.Quality	Shadow Quality	No	Yes	Sets the visual quality of the shadow. Lower quality uses less computing and memory resources.
ShadowEffect2D.ShadowOnly	Shadow Only	No	Yes	Whether to render only the shadow without the node contents.
ShadowEffect2D.Type	Shadow Type	No	Yes	Sets the type of the shadow: - Drop Shadow appears behind or below objects. - Inner Shadow appears inside objects.
SliderConcept.MaxDistanceFromCurve	Maximum Distance From Curve	No	Yes	The distance from the curve where hit testing succeeds.
SpecularAntiAliasingStrength	Specular Anti-Aliasing Strength	No	Yes	Sets the strength of the specular anti-aliasing effect. Higher value results in blurrier specular highlights. For no specular anti-aliasing, set the value to 0. For full specular anti-aliasing, set the value to 1. The default value is 0.25.
SpecularAntiAliasingThreshold	Specular Anti-Aliasing Threshold	No	Yes	Sets the upper limit for the amount of specular anti-aliasing effect to apply. The default value is 0.18.
SpecularColor	Specular Color	No	Yes	The color of the specular reflection.
SpecularExponent	Specular Exponent	No	Yes	Determines the size of the specular highlight.
SpecularFactor	Specular Color Factor	No	Yes	Sets the specular color for the material.
SpecularTexture	Specular Color Texture	No	Yes	Sets the texture that contains the specular color for the material. Use the Specular Color Factor property to filter the value from this texture.
SpotLight	Spot Light	No	Yes	Spot light settings
SpotLightAttenuation	Spot Light Attenuation	No	Yes	Sets the effect that this Spot Light has on nodes that are farther away. Distance of light from the lighted surface is input in a quadratic function, the 3 components are the constant, linear and quadratic coefficients for the distance variable.
SpotLightColor	Spot Light Color	No	Yes	Sets the color of the Spot Light.
SpotLightCutoffAngle	Cutoff	No	Yes	Sets the angle of the light cone in degrees.
SpotLightExponent	Exponent	No	Yes	Defines how fast a fully lit area at the center of the light cone turns into an unlit area.
SpotLightInnerAngle	Inner Angle	No	Yes	Sets the inner angle of the light cone in degrees.
SpotLightRadius	Spot Light Radius	No	Yes	Sets the distance at which the intensity of the Spot Light reaches zero. For infinite distance, set the property value to 0.
StackLayoutConcept.Direction	Direction	No	Yes	Defines the axis along which the stack layout arranges its items.
StackLayoutConcept.Reversed	Reversed	No	Yes	Defines whether the stack layout arranges its items in reverse order.
StateGroupInitialState	Initial State	No	Yes	Allows to define a startup state for a group, if there is no controller property defined.
Tags	Tags	No	Yes	List of tags attached to the item
TextBlock3D.Baseline	Baseline	No	Yes	Font baseline in 3D space units.
TextBlock3D.TwoPassRendering	Two Pass Rendering	No	Yes	Defines whether the Text Block 3D is rendered in two passes. Disabling the two pass rendering improves performance, but can cause invalid rendering results when glyph bounds overlap.
TextBlockConcept.WordWrap	Word Wrap	No	Yes	Sets whether to break long lines into multiple lines to make the text fit within the boundaries of the Text Block node.
TextBox3D.CompositionBackgroundColor	Composition Background Color	No	Yes	Sets the color that highlights the text that the user composes using an input method editor (IME).
TextBox3D.CompositionFontColor	Composition Font Color	No	Yes	Sets the color of the text that the user composes using an input method editor (IME).
TextBox3D.SelectionBackgroundColor	Selection Background Color	No	Yes	Sets the color that highlights the selected text.
TextBox3D.SelectionFontColor	Selection Font Color	No	Yes	Sets the color of the selected text.
TextBoxConcept.CompositionText	Composition Text	No	Yes	Reports the text that the user composes in the Text Box using an input method editor (IME).
TextBoxConcept.CompositionTextBackgroundBrush	Composition Text Background Brush	No	Yes	Sets the brush that highlights the text that the user composes using an input method editor (IME).
TextBoxConcept.CompositionTextForegroundBrush	Composition Text Foreground Brush	No	Yes	Sets the brush for the text that the user composes using an input method editor (IME).
TextBoxConcept.CursorPosition	Cursor Position	No	Yes	Sets the position of the cursor in the text shown in the Text Box node.
TextBoxConcept.CursorPositionMessageArguments.CursorPosition	Current Position	No	No	Contains the current position of the cursor.
TextBoxConcept.CursorPrefab	Cursor Prefab	No	Yes	Sets the prefab template that defines the appearance of the cursor instead of the default cursor.
TextBoxConcept.DisplayText	Display Text	No	Yes	Reports the text that the Text Box displays.
TextBoxConcept.EchoMode	Echo Mode	No	Yes	Sets how the Text Box node shows text: - Normal makes the inserted characters visible. - No Echo makes the inserted characters invisible. - Password makes the inserted character visible for a certain amount of time and then masks the character. Use the Password Masking Character property to set the masking character. The default is a bullet symbol. Use the Password Echo Timeout property to set the time in milliseconds that an inserted character is visible before masking.
TextBoxConcept.EditMode	Edit Mode	No	Yes	Sets how the Text Box node enters the editing state: - Automatic makes the Text Box enter the editing state when focused, and leave the editing state when focus is lost. - Triggered requires the user to trigger the Text Box to enter and leave the editing state.
TextBoxConcept.HasSelection	Has Selection	No	Yes	Indicates whether any of the text in the Text Box node is selected.
TextBoxConcept.HideTextHintWhenEditing	Hide Text Hint When Editing	No	Yes	Sets whether to hide the placeholder content, which you set using the Text Hint Prefab property, when the Text Box node is in the editing state. To hide the placeholder content only when the user enters text in the Text Box node, disable this property.
TextBoxConcept.InputMethodAction	Input Method Action	No	Yes	Sets the label of the user action button on the on-screen keyboard for this Text Box. By default uses the label of the default input method of the operating system.
TextBoxConcept.InputType	Input Type	No	Yes	Sets the input type of the input methods that provide the input layout to let the user enter and edit text of specific type in the Text Box node: - Default for the default input type of the input method editor. - Numeric for numbers - Email for email addresses - URL for URL addresses
TextBoxConcept.IsComposingText	Is Composing Text	No	Yes	Reports the text composition state of the Text Box node.
TextBoxConcept.IsEditing	Is Editing	No	Yes	Reports the editing state of the Text Box node.
TextBoxConcept.MaximumTextLength	Maximum Text Length	No	Yes	Sets the maximum length of text that the user can insert in the Text Box node. The unit is a UTF-8 character and the buffer byte length can be greater for multi-byte characters.
TextBoxConcept.PasswordEchoTimeout	Password Echo Timeout	No	Yes	Sets the time in milliseconds that an inserted character is visible before being masked when using the password echo mode. To use the password echo mode, set the Echo Mode property to Password Echo.
TextBoxConcept.PasswordMaskingCharacter	Password Masking Character	No	Yes	Sets the character that masks each character that the application user enters when using the password echo mode. To use the password echo mode, set the Echo Mode property to Password.
TextBoxConcept.ReadOnly	Read Only	No	Yes	Sets whether the Text Box node is editable. When you enable this property, you can set the text only through the Text property and the user cannot edit the text in the Text Box node.
TextBoxConcept.SelectedTextMessageArguments.SelectionEnd	Selection End	No	No	Contains the end index of the selection.
TextBoxConcept.SelectedTextMessageArguments.SelectionStart	Selection Start	No	No	Contains the index of the character in the beginning of the text selection.
TextBoxConcept.SelectionBackgroundBrush	Selection Background Brush	No	Yes	Sets the brush that highlights the selected text.
TextBoxConcept.SelectionEndCursorPosition	Selection End Cursor Position	No	Yes	The position of the cursor that marks the end of text selection in the Text Box node.
TextBoxConcept.SelectionEndPrefab	Selection End Prefab	No	Yes	Sets the prefab template that defines the appearance of the selection handle at the end of text selection instead of the default handle.
TextBoxConcept.SelectionForegroundBrush	Selection Foreground Brush	No	Yes	Sets the brush for the selected text.
TextBoxConcept.SelectionStartCursorPosition	Selection Start Cursor Position	No	Yes	The position of the cursor that marks the beginning of text selection in the Text Box node.
TextBoxConcept.SelectionStartPrefab	Selection Start Prefab	No	Yes	Sets the prefab template that defines the appearance of the selection handle at the beginning of text selection instead of the default handle.
TextBoxConcept.TextContentMessageArguments.TextFieldContent	Text	No	No	Contains the content of a Text Box node.
TextBoxConcept.TextHintPrefab	Text Hint Prefab	No	Yes	Sets the prefab template for showing placeholder content when the Text Box node is empty.
TextBoxConcept.TextInsertionMessageArguments.Position	Position	No	No	The character index at which to insert text.
TextBoxConcept.TextInsertionMessageArguments.Text	Text	No	No	Sets the text to insert in the Text Box node.
TextBoxConcept.TextKeyNavigationDirection	Text Key Navigation Direction	No	Yes	Sets the text key navigation direction.
TextBoxConcept.TextRangeMessageArguments.EndPosition	End Position	No	No	Sets the index of the last character in the text range.
TextBoxConcept.TextRangeMessageArguments.StartPosition	Start Position	No	No	Sets the index of the first character in the text range.
TextConcept.FontColor	Font Color	No	Yes	Sets the color of the text.
TextConcept.FontMaterial	Font Material	No	Yes	Sets the material whose shader is used to render the text. The shader must use the ContentTexture uniform which is automatically filled with glyph data.
TextConcept.HorizontalPadding	Horizontal Padding	No	Yes	Sets the padding spaces between the content and the left and right boundaries of the Text node.
TextConcept.Overflow	Overflow	No	Yes	Sets the characters that represent the truncated text when the text string to be rendered is too long to fit in the node. The default value is "...".
TextConcept.RemoveSideBearings	Remove Side Bearings	No	Yes	Whether to position the leftmost characters of left-aligned text and rightmost characters of right-aligned text exactly within the boundary of the text node.
TextConcept.Text	Text	No	Yes	Sets the text content that the text node renders. To create a line break press Shift+Enter.
TextConcept.TextHorizontalAlignment	Text Horizontal Alignment	No	Yes	Sets the horizontal alignment of the text.
TextConcept.TextVerticalAlignment	Text Vertical Alignment	No	Yes	Sets the vertical alignment of the text.
TextConcept.VerticalPadding	Vertical Padding	No	Yes	Sets the padding spaces between the content and the top and bottom boundaries of the Text node.
Texture	Texture	No	Yes	The texture of the material.
TextureBrush.RenderTexture	Brush Texture	No	Yes	Texture for brush.
TextureNativeDeploymentTarget	Native Deployment Target	No	Yes	Sets the memory in which to store this texture on your target device.
TextureOffset	Texture Offset	No	Yes	Sets an offset for texture in materials.
TextureTiling	Texture Tiling	No	Yes	Determines the number of times a texture is presented in a material.
TimerTrigger.Interval	Timer Interval (ms)	No	No	The interval in milliseconds on which the trigger is triggered.
ToggleButtonGroupConcept.CurrentButtonIndex	Current Button Index	No	Yes	The index of the Toggle Button that is toggled on in the Toggle Button Group.
ToneMapLinearScale	Tone Map Linear Scale	No	Yes	Sets the scale for the linear tonemap option for the material. When linear tonemapping is used, Kanzi divides all output color by the value of this property.
TrajectoryLayoutConcept.AlignToTangent	Align To Tangent	No	Yes	Whether to align the items in this Trajectory Layout to match the tangent of the trajectory. Vertical trajectories are not supported.
TrajectoryLayoutConcept.CalculatedOffset	Calculated Offset	No	Yes	Reports the current offset of an item in a Trajectory Layout in the proportional range [0, 1].
TrajectoryLayoutConcept.ItemAreaBegin	Item Area Begin	No	Yes	Sets the starting point of the trajectory segment in which the items in this Trajectory Layout are considered fully visible. The value is in the range [0, 1], where 0 is the beginning and 1 is the end of the trajectory. The Node > Visible Amount in Parent property uses this value.
TrajectoryLayoutConcept.ItemAreaEnd	Item Area End	No	Yes	Sets the ending point of the trajectory segment in which the items in this Trajectory Layout are considered fully visible. The value is in the range [0, 1], where 0 is the beginning and 1 is the end of the trajectory. The Node > Visible Amount in Parent property uses this value.
TrajectoryLayoutConcept.OverrideDistance	Override Distance	No	Yes	Sets the distance between the items in this Trajectory Layout. When you do not set this property, the Trajectory Layout calculates the distance automatically.
TrajectoryLayoutConcept.OverrideOffset	Trajectory Override Offset	No	Yes	Sets the offset of an item in a Trajectory Layout. When you do not set this property, the Trajectory Layout sets the offset.
TrajectoryLayoutConcept.StartOffset	Start Offset	No	Yes	Sets the offset of the starting position of the items on the trajectory in the range [0, 1], where 0 is the beginning and 1 is the end of the trajectory.
TrajectoryLayoutConcept.Stretch	Stretch	No	Yes	Whether to scale this Trajectory Layout to match the layout size.
TrajectoryLayoutConcept.Trajectory	Trajectory	No	Yes	Sets the Trajectory along which this Trajectory Layout node arranges its items.
TrajectoryListBox.AllowedScrollAxis	Allowed Scroll Axis	No	Yes	Sets the axis on which you want to allow this Trajectory List Box 3D node to scroll.
TrajectoryListBox.Looping	Looping	No	Yes	Whether to show items in the Trajectory List Box 3D from the beginning after reaching the last item.
TrajectoryListBoxConcept.AlignToTangent	Align To Tangent	No	Yes	Whether to align the Trajectory List Box 3D items to match the tangent of the trajectory.
TrajectoryListBoxConcept.CursorOffset	Cursor Offset	No	Yes	Sets the offset of the position to use to select the active item, in proportional range [0,1].
TrajectoryListBoxConcept.ItemAreaBegin	Item Area Begin	No	Yes	Sets the proportional offset where the part of the trajectory meant for the fully visible Trajectory List Box 3D items starts. Kanzi uses the values of the Item Area Begin and Item Area End properties to calculate the value of the Node.VisibleAmountInParent property for each list item.You can use the VisibleAmountInParent property in shaders to fade out those list items that are not fully visible.
TrajectoryListBoxConcept.ItemAreaEnd	Item Area End	No	Yes	Sets the proportional offset where the part of the trajectory meant for the fully visible Trajectory List Box 3D items ends. Kanzi uses the values of the Item Area Begin and Item Area End properties to calculate the value of the Node.VisibleAmountInParent property for each list item.You can use the VisibleAmountInParent property in shaders to fade out those list items that are not fully visible.
TrajectoryListBoxConcept.ScrollPosition	Scroll Position	No	Yes	Sets the scroll position of the Trajectory List Box 3D along the x and y axes as a relative position within the list box area. Use this property to move the list to a scroll position immediately, without scrolling. To update the scroll position with a binding, use a two-way or to-source binding.
TrajectoryListBoxConcept.Spacing	Spacing	No	Yes	Sets the distance between the items in the Trajectory List Box 3D.
TrajectoryListBoxConcept.Trajectory	Trajectory	No	Yes	Sets the trajectory along which the Trajectory List Box 3D arranges its items.
TrajectoryListBoxDraggingAccelerationCoefficient	Dragging Acceleration	No	Yes	Sets the acceleration of the Trajectory List Box 3D when the user scrolls the Trajectory List Box 3D by dragging the pointer. The higher the value, the quicker the Trajectory List Box 3D reaches its final position. The default value is 80.
TrajectoryListBoxDraggingDragCoefficient	Dragging Drag	No	Yes	Sets the amount that drag affects the movement of the Trajectory List Box 3D when the user scrolls the Trajectory List Box 3D by dragging the pointer. The lower the value, the higher the drag and the quicker the scrolling stops. The default value is 150.
TrajectoryListBoxDraggingImpulseFactor	Dragging Impulse	No	Yes	Sets the amount of impulse to generate from the pointer movement when the user scrolls the Trajectory List Box 3D by dragging the pointer.
TrajectoryListBoxMaximumNumberOfTouches	Maximum Number of Touches	No	Yes	Sets the maximum number of touch points allowed on the Trajectory List Box 3D area for scrolling.
TrajectoryListBoxMinimumNumberOfTouches	Minimum Number of Touches	No	Yes	Sets the minimum number of touch points required on the Trajectory List Box 3D area for scrolling.
TrajectoryListBoxRecognitionThreshold	Recognition Threshold	No	Yes	Sets the distance in pixels that the pointer has to move for the scrolling to start in the Trajectory List Box 3D.
TrajectoryListBoxSensitivity	Scroll Sensitivity	No	Yes	Sets the amount that the scroll value changes relative to the movement of the pointer on the scroll view plane of the Trajectory List Box 3D. The default value 1 makes the Trajectory List Box 3D scroll the same amount as the user drags the pointer. For example, to set the Trajectory List Box 3D to scroll twice the amount that the user drags the pointer, set the value of the property to 2.
TrajectoryListBoxSlidingAccelerationCoefficient	Sliding Acceleration	No	Yes	Sets the acceleration of the Trajectory List Box 3D after the user releases the pointer with which they scroll the Trajectory List Box 3D. The higher the value, the quicker the Trajectory List Box 3D reaches the scroll target. The default value is 40.
TrajectoryListBoxSlidingDragCoefficient	Sliding Drag	No	Yes	Sets how much drag affects the movement of the Trajectory List Box 3D after the user releases the pointer with which they scroll the Trajectory List Box 3D. The lower the value, the higher the drag and the quicker the scrolling of the Trajectory List Box 3D stops. The default value is 80.
TrajectoryListBoxSwipeDistance	Swipe Distance	No	Yes	Sets the distance that a swipe sends the scroll value in the Trajectory List Box 3D, relative to the speed of the pointer.
TriggerActionItem.ForwardedMessageArguments	Forwarded Arguments	No	Yes	The arguments of the message to forward
TrySetFocusAction.TargetItem	Target Item	No	No	Target item to be focused
ValueAccumulator.Autoplay	Autoplay	No	Yes	Sets whether the Value Accumulator starts automatically when it is attached to the node.
ValueAccumulator.BoundType	Bound Type	No	Yes	Sets how the Value Accumulator limits the total accumulated value between the minimum and maximum value boundaries.
ValueAccumulator.IncrementTimeInterval	Increment Time Interval	No	Yes	Sets the frequency of increments in milliseconds.
ValueControlledExclusiveActivityHostConcept.ControllerProperty	Controller Property	No	Yes	Sets the property type that the Exclusive Activity Host node uses to switch between its child Activity nodes.
ValueControlledExclusiveActivityHostConcept.DataSourceControllerPropertyPath	Data Source Controller Property Path	No	Yes	Sets the path in the Data Source object of an Exclusive Activity Host node to a Data Object item that the Exclusive Activity Host node uses as the Controller Property.
Viewport2D.Camera	Camera	No	Yes	Sets which camera to use in scenes rendered by the selected Viewport 2D. If not set, Kanzi uses the camera in the scene.
Viewport2D.HitTestCamera	Hit Test Camera	No	Yes	Sets which hit test camera to use in scenes rendered by the selected Viewport 2D. If not set, Kanzi uses the camera in the scene.
Viewport2D.RenderPass	Render Pass	No	Yes	The RenderPass used for rendering the Scene for the Viewport. Instantiated from the RenderPassPrefab. Set internally by Kanzi whenever RenderPassPrefabProperty changes.
Viewport2D.RenderPassPrefab	Render Pass Prefab	No	Yes	Sets which render pass prefab will be used to instantiate the render pass tree.
Window.MetricsType	Metrics Type	No	No	Defines the type of the coordinate system for the window metrics.
Window.Orientation	Orientation	No	No	The orientation of the window.
WriteLogAction.LogText	Log Text	No	No	The text to write to the Kanzi Studio Log window when a trigger executes this action.