Text Block 2D

Text Block 2D properties

Name	Description	Inherited	Exported to Kanzi Engine
Text	Sets the text content that the text node renders. To create a line break press Shift+Enter.	No	Yes

Text Block 2D available properties

Name	Description	Inherited	Exported to Kanzi Engine
Active Activity Index	The index of the active Activity in the Data-Driven Exclusive Activity Host. After instantiating all Activity from a Data Source, this property refers to the only currently active Activity in this Data-Driven Exclusive Activity Host. To deactivate all the Activities in this Data-Driven Exclusive Activity Host, set this property to -1.	No	Yes
Activity Source	The data object that provides the data for this Activity node.	No	Yes
Activity Status	Sets the possible states of the Activity when its Activity Host activates or deactivates that Activity.	No	Yes
Activity Template	If set, the Data-Driven Exclusive Activity Host uses this prefab for Activity nodes that it creates.	No	Yes
Actual Layout Height	The calculated height of the node when used in a layout.	No	Yes
Actual Layout Width	The calculated width of the node when used in a layout.	No	Yes
Alpha Cutoff	Sets the cutoff threshold for alpha cutting. If the alpha value is less than the value of this property, Kanzi discards the fragment. The default value is 0.5.	No	Yes
Ambient Color	The color of the material when lights are not present.	No	Yes
Aspect Ratio	Determines the proportion of width and height. You cannot set both the Aspect Ratio and both, Width and Height.	No	Yes
Auto Press Interval	Sets the time in milliseconds after which a button that the user keeps pressed down sends the Button: Click message. While the user holds the button down, the button keeps sending the Button: Click message at the time interval set by this property. To disable the behavior, set to 0.	No	Yes
Background Brush	The background brush to paint the background of 2D nodes.	No	Yes
Base Color Factor	Sets the base color for the material.	No	Yes
Base Color Texture	Sets the texture that contains the base color for the material. Use the Base Color Factor property to filter the value from this texture.	No	Yes
Baseline	Font baseline in 3D space units.	No	Yes
Blend Intensity	Controls the intensity of materials that are blended on top of an existing color. Attached property enables overriding of the blend intensity of the used materials at render pass or object node level.	No	Yes
Blend Mode	Sets how to blend colors. Color Blending: - Additive adds the source pixels to the destination pixels. - Multiply multiplies the source and destination pixels. - Screen adds the source and destination pixels and subtracts from the result the product of the source and destination. - Alpha: Automatic uses premultiplied or non-premultiplied alpha depending on the value of the “Premultiply Alpha” property in the project or an image. - Alpha: Non-premultiplied is a legacy mode. For non-premultiplied input use the Alpha: Mixed mode. - Alpha: Premultiplied expects premultiplied alpha RGBA in the source pixels and blends the source pixels on top of the destination pixels. This is the default and recommended mode for alpha blending. - Alpha: Mixed expects non-premultiplied alpha RGBA in the source pixels, and blends the source pixels with the destination framebuffer. Alpha Compositing: - Opaque disables blending and replaces the destination pixels with the source pixels. - Clear sets the destination pixels to transparent black. - Exclusive Or draws the non-overlapping source and destination pixels. - Source Atop discards those source pixels that do not cover destination pixels and draws the rest of the source pixels over destination pixels. - Source In draws those source pixels that cover destination pixels and discards all destination pixels. - Source Out draws the source pixels with alpha reduced by the inverse of the destination alpha, and discards all destination pixels. - Destination Atop discards those destination pixels that are not covered by source pixels, and draws the rest of the destination pixels over source pixels. - Destination In draws only those destination pixels that intersect with the source pixels, and discards all source pixels. - Destination Out draws the destination pixels with alpha reduced by the inverse of the source alpha, and discards all source pixels. - Destination Over draws the destination pixels over the source pixels. Advanced Color Blending: - Multiply (advanced khr) is similar to the Multiply mode but it screens the alpha. - Overlay multiplies dark pixels and screens light pixels. - Darken compares the destination and source pixels and selects the darker one. - Lighten compares the destination and source pixels and selects the lighter one. - Color Burn darkens the destination to reflect the color of the source. - Color Dodge lightens the destination to reflect the color of the source. - Hard Light multiplies with dark source color and screens with light source color. - Soft Light burns with dark source color and dodges with light source color. - Difference uses the difference of the source and destination pixels. - Exclusion is similar to difference but the result is lower in contrast. - HSL Hue uses the hue of the source, and the luminosity and saturation of the destination. - HSL Saturation uses the saturation of the source, and the hue and luminosity of the destination. - HSL Color uses the hue and saturation of the source, and the luminosity of the destination. - HSL Luminosity uses luminosity of the source, and the jue and saturation of the destination. The advanced color blending modes require the GL_KHR_blend_equation_advanced and GL_KHR_blend_equation_advanced_coherent OpengGL extensions.	No	Yes
Blur Quality	Sets the visual quality of the blur. Lower quality uses less computing and memory resources.	No	Yes
Blur Radius	Sets the amount of blur by defining the radius of the circular area of pixels that blend into each other. The blur radius also determines the distance in pixels that the blur expands the render area by extending outward from an edge, unless you enable the Masked Blur property. To disable the blur effect, set this property to 0. The default value is 8.	No	Yes
Bottom Image	The image to use in middle of the bottom row.	No	Yes
Bottom-Left Image	Image to use in the bottom-left corner.	No	Yes
Bottom-Right Image	The image to use in the bottom-right corner.	No	Yes
BRDF Lookup Table	Gets the Bidirectional Reflectance Distribution Function (BRDF) lookup table for the material. The BRDF table is a texture that contains precomputed information about how light reflects off a material. You can use it to improve rendering quality.	No	Yes
Bring Activated Activity To Front	Sets whether to show the activated Activity in front within its Parallel Activity Host. This property affects the z-order of the activated Activity within the same Activity priority layer: - When enabled, the Activity is shown in front. - When disabled, the z-order of the activated child Activity is determined by the order in which you added that Activity to the parent Parallel Activity Host. This is the default behavior.	No	Yes
Brush Color	Color for brush. Set alpha to 0 to disable brush.	No	Yes
Brush Horizontal Tiling	Horizontal Tiling for the brush. Affects the scale of texture coordinates.	No	Yes
Brush Modulate Color	Modulation color for brush. Effects brush rendering that needs color modulation.	No	Yes
Brush Texture	Texture for brush.	No	Yes
Brush Vertical Tiling	Vertical Tiling for the brush. Affects the scale of texture coordinates.	No	Yes
Cache Valid	Indicates whether the node is cached. To disable the cache for one frame, disable this property.	No	Yes
Caching Mode	Sets the caching mode of this node: - Disabled sets Kanzi to render the node and its descendants normally, without caching. This is the default. - Enabled sets Kanzi to cache the node and its descendants and render the node from the cache image until you invalidate the cache by disabling the Cache Valid property. - Automatic sets Kanzi to automatically update the cache of the node whenever the content of the node or its descendants change.	No	Yes
Calculated Offset	Reports the current relative offset of an item in the Grid List Box in proportional range [0, 1].	No	Yes
Calculated Offset	Reports the current offset of an item in a Trajectory Layout in the proportional range [0, 1].	No	Yes
Camera	Sets which camera to use in scenes rendered by the selected Viewport 2D. If not set, Kanzi uses the camera in the scene.	No	Yes
Center Image	The image to use in the center.	No	Yes
Character Spacing	Sets the character spacing in pixels.	No	Yes
Clear Coat Normal Scale	Sets the clear coat normal scale for the material. Use the scale to set the intensity of the Clear Coat Normal Texture.	No	Yes
Clear Coat Normal Texture	Sets the texture that contains a clear coat normal map for the material. Use the Clear Coat Normal Scale property to scale the texture value.	No	Yes
Clear Coat Roughness Factor	Sets the roughness of the outer clear coat layer for the material: 0 represents a smooth, glossy surface, and 1 represents a rough, diffuse surface.	No	Yes
Clear Coat Roughness Texture	Sets the texture that contains a clear coat roughness map for the material. Kanzi reads the roughness from the Green channel of the texture. Use the Clear Coat Roughness Factor property to scale the roughness from this texture.	No	Yes
Clear Coat Strength Factor	Sets the clear coat strength for the material: 0 represents a material with no clear coat, and 1 represents a full strength clear coat.	No	Yes
Clear Coat Strength Texture	Sets the texture that contains a clear coat strength map for the material. Kanzi reads the strength from the Red channel of the texture. Use the Clear Coat Strength Factor property to scale the strength from this texture.	No	Yes
Clip Children	Sets whether to clip the child nodes of this node. Kanzi clips the child nodes whose bounding box is completely outside of the bounding box of their parent node. Use this property with layout nodes. The child nodes can use only translation transformation.	No	Yes
Code Behind Source	Sets the metaclass name of the code behind class for this node.	No	Yes
Column	The column into which grid layout places the item.	No	Yes
Column Span	Defines the number of columns an item in a grid layout occupies.	No	Yes
Command	The command executed by a UI control	No	Yes
Composition Brush	The brush to use to compose 2D nodes to screen.	No	Yes
Content Gradient	Sets the gradient along which the content fades out: - Start sets the minimum intensity at which the content starts to fade out. - Softness sets the difference in intensity it takes for the content to disappear. For a perfectly smooth gradient, set Start to 0 and Softness to 1. The default value [ 0.0, 0.19 ] makes the content fade out quickly before the outline fade-out starts.	No	Yes
Content Mask	Sets the color that masks color components relevant to the outline calculation. The comparison value is the result of a dot product between the mask and the content RGBA color value. By default Kanzi calculates the outline only from the alpha value.	No	Yes
Content Stretch	Sets how the content that belongs to this node is stretched (as opposed to manipulating the actual node size).	No	Yes
Content Threshold	Sets the threshold at which the value Kanzi calculates using the content mask is considered valid. When the value calculated from masking the content exceeds this value, that pixel is part of the outlined area.	No	Yes
Controller Property	Sets the property type that the Exclusive Activity Host node uses to switch between its child Activity nodes.	No	Yes
Custom Asset Thumbnail	When enabled, the asset will have selected image as thumbnail instead of the generated one.	No	No
Cyclic Focus Navigation	Sets whether the focus chain navigation within the focus scope is cyclic. When you enable this property: - When the user navigates in the forward direction and the focus reaches the last focusable UI element of the focus scope, the focus navigation moves to the first focusable UI element. - When the user navigates in the backward direction and the focus reaches the first focusable UI element of the focus scope, the focus navigation moves to the last focusable UI element.	No	Yes
Data Context	Source of data for this node and its descendants	No	Yes
Data Source Controller Property Path	Sets the path in the Data Source object of an Exclusive Activity Host node to a Data Object item that the Exclusive Activity Host node uses as the Controller Property.	No	Yes
Description	Add a description of the purpose of this item. To export descriptions to a plain text file, select File > Export > Export Descriptions. When you export the kzb file, this description is not included in the exported file.	No	No
Detail Base Color Factor	Sets the detail base color for the material. The detail base color is alpha blended with the standard base color.	No	Yes
Detail Base Color Texture	Sets the detail texture that contains the base color for the material. Use the Detail Base Color Factor property to filter the value from this texture. The detail base color is alpha blended with the standard base color. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Clear Coat Normal Scale	Sets the detail clear coat normal scale for the material. Use the scale to set the intensity of the Detail Clear Coat Normal Texture.	No	Yes
Detail Clear Coat Normal Texture	Sets the detail texture that contains a clear coat normal map for the material. Use the Detail Clear Coat Normal Scale property to scale the texture value.	No	Yes
Detail Clear Coat Roughness Texture	Sets the detail texture that contains a clear coat roughness map for the material. Use the Clear Coat Roughness Factor and Clear Coat Roughness Texture properties to scale the roughness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Clear Coat Strength Texture	Sets the detail texture that contains a clear coat strength map for the material. Kanzi reads the strength from the Red channel of the texture. Use the Clear Coat Strength Factor and Clear Coat Strength Texture properties to scale the strength from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Diffuse Color Factor	Sets the detail diffuse color for the material. Kanzi alpha blends the detail diffuse color with the standard diffuse color.	No	Yes
Detail Diffuse Color Texture	Sets the detail texture that contains the diffuse color for the material. Use the Detail Diffuse Color Factor property to filter the value from this texture. Kanzi alpha blends the detail diffuse color with the standard diffuse color. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Emissive Factor	Sets the color of the light that is emitted from a detail texture for the material. This color affects the local material rendering, but the light is not cast to other objects. The detail emissive light is alpha blended with the standard emissive light. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Emissive Texture	Sets the detail texture that contains the light emitted from the material. Use the Detail Emissive Factor property to scale the value from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Glossiness Texture	Sets the detail texture that contains a glossiness map for the material. Kanzi reads the glossiness from the Alpha channel of this texture. Use the Glossiness Factor and Glossiness Texture properties to scale the glossiness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Metallic Texture	Sets the detail texture that contains a metallic map for the material. Kanzi reads the metalness from the Blue channel of this texture. Use the Metallic Factor and Metallic Texture properties to scale the metalness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Normal Scale	Sets the detail normal scale for the material. Use the scale to set the intensity of the Detail Normal Texture.	No	Yes
Detail Normal Texture	Sets the detail texture that contains a normal map for the material. Use the Detail Normal Scale property to scale the texture value.	No	Yes
Detail Occlusion Strength	Sets the detail occlusion strength for the material. Use the strength to set the intensity of the Detail Occlusion Texture.	No	Yes
Detail Occlusion Texture	Sets the detail texture that contains an occlusion map for the material. Kanzi reads the occlusion from the Red channel of this texture. Use the Detail Occlusion Strength property to scale the occlusion from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Roughness Texture	Sets the detail texture that contains a roughness map for the material. Kanzi reads the roughness from the Green channel of the texture. Use the Roughness Factor and Roughness Texture properties to scale the roughness from this texture. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Specular Color Factor	Sets the detail specular color for the material. Kanzi alpha blends the detail specular color with the standard specular color.	No	Yes
Detail Specular Color Texture	Sets the detail texture that contains the specular color for the material. Use the Detail Specular Color Factor property to filter the value from this texture. Kanzi alpha blends the detail specular color with the standard specular color. Use the Detail Texture Tiling and Detail Texture Offset properties to set UVs for this texture.	No	Yes
Detail Texture Offset	Sets the detail texture offset for the material. Kanzi adds this value to the UVs to produce a second set of detail UVs to use for all detail texture properties.	No	Yes
Detail Texture Tiling	Sets the detail texture tiling factor for the material. Kanzi multiplies this value by the UVs to produce a second set of detail UVs to use for all detail texture properties.	No	Yes
Diffuse Color	The color of the material when it is lit by a light.	No	Yes
Diffuse Color Factor	Sets the diffuse color for the material.	No	Yes
Diffuse Color Texture	Sets the texture that contains the diffuse color for the material. Use the Diffuse Color Factor property to filter the value from this texture.	No	Yes
Direction	Defines the axis along which the stack layout arranges its items.	No	Yes
Disable KZB Export	Disables the exporting of the item into KZB. Can be used for, e.g. letting items out from certain profiles. The disabled items are always included in preview.	No	No
Disable Render Target Clear Color	Do not clear render target buffers before rendering into it even if necessary.	No	Yes
Down On Hover	Whether holding a finger on the device screen and moving it over the button transitions the button to the down state.	No	Yes
Effect	Reports the runtime effect instance that this node uses. Kanzi sets the value of this property internally when the value of the Effect Prefab property in this node changes.	No	Yes
Effect Prefab	The 2D Effect to use for this node.	No	Yes
Effectively Enabled	Indicates whether this node and its ancestor nodes are enabled. Use this property in state managers and bindings to observe whether a node is effectively enabled. To enable or disable a node, use the Enabled property. When a node is effectively disabled: - When that node is focused, it receives key input until the focus moves to another node. - When that node is not focused, it is not part of the focus chain and does not receive key input.	No	Yes
Emissive Color	The color of the light that is emitted from the material surface.	No	Yes
Emissive Factor	Sets the color of the light that is emitted from the material. This color affects the local material rendering, but the light is not cast to other objects.	No	Yes
Emissive Texture	Sets the texture that contains the light emitted from the material. Use the Emissive Factor property to scale the value from this texture.	No	Yes
Enabled	Whether this node is enabled. When you disable this property in a node, that node and its descendant nodes in the same overlay focus scope are effectively disabled. Effectively disabling a node removes that node from the focus chain and cancels all the active input manipulators.Use the Effectively Enabled property to observe whether a node is effectively enabled.	No	Yes
Environment Ambient Factor	Sets the strength of the cubemap texture to use for ambient environment light. Use the Environment Ambient Texture property to set the cubemap texture. The ambient environment light affects diffuse lighting in image based lighting.	No	Yes
Environment Ambient Texture	Sets the cubemap to use for the ambient environment light for the material. This cubemap affects the diffuse lighting during image based lighting. Use the Environment Ambient Factor property to set the strength of the cubemap texture.	No	Yes
Environment Reflection Factor	Sets the strength of the cubemap texture to use for specular environment light. Use the Environment Reflection Texture property to set the cubemap texture. The specular environment light affects reflective lighting in image based lighting.	No	Yes
Environment Reflection Texture	Sets the cubemap to use for the specular environment light for the material. This cubemap affects reflective lighting during image based lighting. Use the Environment Reflection Factor property to set the strength of the cubemap texture.	No	Yes
Export in Asset Package	When enabled, this item is exported into asset package if this project is saved as one.	No	No
Exposure	Sets the exposure compensation for the material. The exposure compensation emulates camera exposure by controlling the total amount of light rendered. Use a negative value to darken the rendered image, and a positive value to lighten the image. Exposure is exponential: 1.0 is twice as bright as 0.0, and -1.0 is half as bright as 0.0.	No	Yes
Fixed Character Width	When set, overrides the font advance widths to make each character take a fixed amount of space specified in pixels.	No	Yes
Focus On Press	Sets where to set the focus when the user presses the node that has this property: - None (0) keeps the focus where it was. This is the default. - Node (1) sets the focus to the node. - Node or ancestor (2) sets the focus to the node or, if that fails, to the closest focusable ancestor node. - Node or overlay (3) sets the focus to the node or, if that fails, to the closest ancestor overlay scope, which then forwards the focus according to its settings. The descendants of the node where you set this property inherit value of the property.	No	Yes
Focus Order	Sets the focus chain order of the node within the focus scope.	No	Yes
Focus Scope Type	Sets the type of the focus scope node: - Group groups focusable nodes. - Fence keeps the focus chain navigation inside the scope and does not allow the focus chain navigation to enter or leave that scope. - Modal overlay blocks the key and touch input that originates outside of its boundaries and keeps the focus navigation within the scope boundaries. - Auto-Closing Modal overlay loses focus when key or touch input originates from a node that is outside of its node tree, and suppresses that input. - Modeless overlay propagates the key and touch input that originates outside of its boundaries to the nodes outside of its boundaries. - Auto-Closing Modeless overlay loses focus when key or touch input originates from a node that is outside of its boundaries, and propagates that input.	No	Yes
Focus State	Reports the focus state of a node: - No focus (0) indicates that the node is not focused. For a focus scope node indicates that none of the nodes in the scope have focus. - Logical focus (1) indicates that the node is the logical focus node of an overlay-type focus scope. For a focus scope node indicates that one of the nodes in that scope is the logical focus node. - Key focus (2) indicates that the node is the key focus node of the application and receives key input. For a focus scope node indicates that one of the nodes in that scope is the key focus node. Use this property in state managers and bindings to implement focus states in the UI nodes. To observe whether a node is the key focus node, you can use the boolean Focus > Focused property.	No	Yes
Focusable	Indicates whether the node can receive focus.	No	Yes
Focused	Indicates whether the node has the key focus.	No	Yes
Font Color	Sets the color of the text.	No	Yes
Font Family	The font family used to render the text.	No	Yes
Font Hinting Preference	Sets the hinting preference of the font. - No hinting: Render text without hinting the outlines of glyphs. - Native hinting: Prefer native hinter of the font over the auto-hinter of the rasterizer. - Auto hinting: Prefer auto-hinter of the rasterizer over the native hinter of the font.	No	Yes
Font Material	Sets the material whose shader is used to render the text. The shader must use the ContentTexture uniform which is automatically filled with glyph data.	No	Yes
Font Size	Sets the size of the font in pixels.	No	Yes
Font Style	Sets the style of the FontStyleConcept.	No	Yes
Font Weight	Sets the weight of the FontStyleConcept.	No	Yes
Force Composition	Force rendering to composing target even if not otherwise necessary.	No	Yes
Foreground Brush	The foreground brush to paint the foreground of 2D nodes.	No	Yes
Foreground Hint	Give a hint of the type of the foreground of 2D nodes: - None renders the background brush after rendering the node. - Translucent renders the background brush before the content of the node. - Occluding renders the background brush.	No	Yes
Fractional Character Width	Sets whether Kanzi uses fractional or rounded character widths to lay out text. In most cases fractional widths provide the best result. However, with small font sizes, fractional widths can cause the characters to run together or have too much space, making it difficult to read. - When enabled, Kanzi uses fractional character widths, which means that the spacing between characters varies and can be a fraction of a pixel. - When disabled, Kanzi uses character widths rounded to the nearest pixel. Disable fractional widths when you want to fix character spacing in whole-pixel increments and prevent characters in small font sizes from running together.	No	Yes
Global Ambient Color	The color that is multiplied automatically with the “Ambient” property of the materials in the scene.	No	Yes
Glossiness Factor	Sets the glossiness of the material: 0 represents a rough, diffuse surface, and 1 represents a smooth, glossy surface.	No	Yes
Glossiness Texture	Sets the texture that contains a glossiness map for the material. Kanzi reads the glossiness from the Alpha channel of this texture. Use the Glossiness Factor property to scale the glossiness from this texture.	No	Yes
Glyph Texture	The automatic texture of the glyph cache.	No	Yes
Hit Test Camera	Sets which hit test camera to use in scenes rendered by the selected Viewport 2D. If not set, Kanzi uses the camera in the scene.	No	Yes
Hit Testable	When enabled, the node can be hit tested. Enabling Hit Testable for a 2D node enables hit testing only for that node. Enabling Hit Testable for a 3D node enables hit testing also for the child nodes. Kanzi hit tests 3D nodes using the default Camera node or the Hit Test Camera node of the active Scene node.	No	Yes
Hold Interval	Sets the amount of time in milliseconds that the user must hold the button pressed down for Kanzi to recognize it as a long-press gesture. To disable the long-press gesture, set to 0.	No	Yes
Horizontal Alignment	The alignment in horizontal direction the node should use when it resides under a layout.	No	Yes
Horizontal Fit	Whether to horizontally scale the glyphs to make them fit into the Layout Width of the Text Block. To adjust the scale, use the Horizontal Fit Scale Limits property.	No	Yes
Horizontal Fit Scale Limits	When the Horizontal Fit property is enabled, sets the minimum and maximum scale for glyphs when the width of text in a Text Block does not match the Layout Width of that Text Block. For example: - Min property field set to 1.0 does not squeeze the glyphs, while 0.5 squeezes the glyphs to half their size. - Max property field set to 1.0 does not stretch the glyphs, while 2.0 stretches the glyphs to double their size.	No	Yes
Horizontal Margin	Sets the horizontal space between this node and other nodes that are adjacent to this node in a layout. To set the Horizontal Margin property fields in a binding use: - Vector_X to access the Left property field - Vector_Y to access the Right property field	No	Yes
Horizontal Padding	Sets the padding spaces between the content and the left and right boundaries of the Text node.	No	Yes
Hover	Indicates whether a node is the foremost hit testable node under the cursor.	No	Yes
Image	The image to display.	No	Yes
Index In Group	Sets the index of the Button in the Toggle Button Group to which that Button is registered. If a Button does not have local value for this property, it is not registered to the ancestor Toggle Button Group. When set to -1 the Toggle Button Group assigns an index for the Button.	No	Yes
Invert Content Mask	Whether to invert the value that Kanzi calculates using content masking.	No	Yes
Invert Mask	Whether to invert the mask so that transparent areas become opaque and opaque areas become transparent.	No	Yes
Is Down	Indicates whether the button is pressed and in the down state.	No	Yes
Is Value Changing	Whether the value is currently changing.	No	Yes
Item Index	Reports the index of the item in the List Box Item Container.	No	Yes
Layout Height	The height of the node when used in a layout. Overrides the default bounds of the item.	No	Yes
Layout Transformation	The 2D transformation to be applied before layouting.	No	Yes
Layout Width	The width of the node when used in a layout. Overrides the default bounds of the item.	No	Yes
Left Image	The image to use in the center-left.	No	Yes
Line Spacing	Sets the line spacing in multiples of the normal line height of the selected FontStyleConcept.	No	Yes
Mask Channel	Sets the texture channel to use as the input for the mask: - Alpha uses the alpha channel from the texture. This is the default. - Red uses the red color channel from the texture. - Green uses the green color channel from the texture. - Blue uses the blue color channel from the texture. - Luminance uses the luminance calculated from the red, green, and blue channels.	No	Yes
Mask Height	Sets the height of the mask to use in a layout. This value overrides the height of the texture that you use as the mask.	No	Yes
Mask Horizontal Alignment	Sets the horizontal alignment of the mask effect: - Left aligns the left edge of the mask with the left edge of the node. This is the default. - Right aligns the right edge of the mask with the right edge of the node. - Center aligns the mask horizontally to the center of the node. - Stretch stretches the mask horizontally to fit the node from the left edge to the right edge.	No	Yes
Mask Offset	Sets the mask offset along the X and Y axes in pixels. Kanzi applies the mask offset after stretch, alignment, and scale.	No	Yes
Mask Scale	Sets the factor by which to scale the mask. Kanzi applies the scale after stretch and alignment.	No	Yes
Mask Strength	Sets the strength of the mask effect in the range from 0 to 1: - 0 disables the mask effect. - 1 applies the mask at full strength. This is the default. - Any value between 0 and 1 partially applies the mask as if the non-masked result was blended with the fully masked version.	No	Yes
Mask Stretch	Sets the stretch mode of the mask effect: - None disables stretching. This is the default. - Fill stretches the mask to fill the node. - Uniform stretches the mask using uniform scaling to fill the node in either vertical or horizontal direction, whichever requires smaller scale. - Uniform To Fill stretches the mask using uniform scaling to fill the node in either vertical or horizontal direction, whichever requires larger scale. - Repeat does not stretch the mask, and allows the mask to repeat outside of its area based on the mask texture wrap mode.	No	Yes
Mask Texture	The texture for masking other texture or color.	No	Yes
Mask Texture	Sets the mask texture. The default is no texture.	No	Yes
Mask Texture Offset	Sets an offset for mask in materials.	No	Yes
Mask Texture Tiling	Determines the number of times a mask is presented in a material	No	Yes
Mask Vertical Alignment	Sets the vertical alignment of the mask effect: - Bottom aligns the bottom edge of the mask with the bottom edge of the node. - Top aligns the top edge of the mask with the top edge of the node. This is the default. - Center aligns the mask vertically to the center of the node. - Stretch stretches the mask vertically to fit the node from the top edge to the bottom edge.	No	Yes
Mask Width	Sets the width of the mask to use in a layout. This value overrides the width of the texture that you use as the mask.	No	Yes
Masked Blur	Sets whether to blur only the pixels whose alpha channel value is not zero. When you enable this property, the blur does not spread to fully transparent pixels and the edges of the content stay sharp. The default value is false.	No	Yes
Maximum Distance From Curve	The distance from the curve where hit testing succeeds.	No	Yes
Maximum Value	The maximum value that the range allows.	No	Yes
Metallic Factor	Sets the metalness of the material: 0 represents a non-metallic or dielectric object, and 1 represents a metallic object.	No	Yes
Metallic Texture	Sets the texture that contains a metallic map for the material. Kanzi reads the metalness from the Blue channel of this texture. Use the Metallic Factor property to scale the value from this texture.	No	Yes
Minimum Value	The minimum value that the range allows.	No	Yes
Multisample Level	Sets the amount of multisample anti-aliasing to apply to the temporary composition targets to which Kanzi renders this node.	No	Yes
Node.Path	Full path to the node.	No	Yes
Normal Scale	Sets the normal scale for the material. Use the scale to set the intensity of the Normal Texture.	No	Yes
Normal Texture	Sets the texture that contains a normal map for the material. Use the Normal Scale property to scale the texture value.	No	Yes
Normalized Value	The current value normalized to range [0, 1].	No	Yes
Occlusion Strength	Sets the occlusion strength for the material. Use the strength to set the intensity of the Occlusion Texture.	No	Yes
Occlusion Texture	Sets the texture that contains an occlusion map for the material. Use the Occlusion Strength property to scale the occlusion from the texture.	No	Yes
Off-Screen Rendering	When set and the node has an explicitly set render target, do not render the resulting framebuffer to screen.	No	Yes
Opacity	Opacity of the node.	No	Yes
Outline Color	Sets the color of the outline.	No	Yes
Outline Inner Softness	Sets the softness of the outline relative to its width inside the content area. For a sharp outline, set to 0. For a fade-in that takes the complete outline width to reach maximum value, set to 1. By default, this property uses the value of the Outline Softness property.	No	Yes
Outline Inner Width	Sets the width of the outline in pixels inside the content area. By default, this property uses the value of the Outline Width property.	No	Yes
Outline Method	Sets the method for outline calculation: - Box search. Potentially consumes less memory, slower. - Two-pass search. Potentially consumes more memory, faster. This the default.	No	Yes
Outline Softness	Sets the softness of the outline. For a sharp outline, set to 0. For a fade-in that takes the complete outline width to reach maximum value, set to 1. The default value is 0.27.	No	Yes
Outline Texture	Sets the texture to apply to the outline. Kanzi applies to the outline only the top row of pixels from this texture. Set Outline Color to the color with which you want to modulate the colors in this texture.	No	Yes
Outline Texture Offset	Sets the relative starting offset for sampling the outline texture. The default value is 0.0.	No	Yes
Outline Texture Tiling	Sets the number of times the texture wraps around within the outline area. To repeat a texture, set its Wrap Mode to Repeat. The default value is 1.0	No	Yes
Outline Width	Sets the width of the outline in pixels outside the content area. The default value is 4 pixels.	No	Yes
Overflow	Sets the characters that represent the truncated text when the text does not fit in this node. The default value is ‘…’. By default, Kanzi truncates the text at the end. Use the Truncation Direction property to set the part of the text that you want to truncate.	No	Yes
Override Shadow Offset	Sets the offset of the shadow from the object along the x and y axes in pixels. When you set this property, the Shadow Angle and Shadow Distance properties have no effect. To disable the offset override, remove this property.	No	Yes
Perspective Transformation	The 3D transformation to be applied after layouting.	No	Yes
Perspective Transformation FOV	The 3D transformation field of view (degrees) to be applied after layouting.	No	Yes
Perspective Transformation Mode	Defines the mode of operation for the coordinate system and field of view.	No	Yes
Perspective Transformation Origin	The 3D transformation origin to be used for perspective transformation on this or child nodes.	No	Yes
Perspective Transformation Pivot	The 3D pivot point in relative coordinates.	No	Yes
Pixel Format	The pixel format of the node if rendering to a texture.	No	Yes
Remove Side Bearings	Whether to position the leftmost characters of left-aligned text and rightmost characters of right-aligned text exactly within the boundary of the text node.	No	Yes
Render Pass Prefab	Sets which render pass prefab will be used to instantiate the render pass tree.	No	Yes
Render Self	Whether the node renders itself. Does not affect the rendering of child nodes.	No	Yes
Render Target	Forces the node to be rendered into a given render target texture. When set to “No Target”, regular conditions whether node is rendered to a texture, such as opacity and rotation, are applied.	No	Yes
Render Target Minimum Height	Sets the minimum height of implicitly generated render targets.	No	Yes
Render Target Minimum Width	Sets the minimum width of implicitly generated render targets.	No	Yes
Render Target Reallocation Limit	The change in size that triggers reallocation of a render target.	No	Yes
Render Transformation	The 2D transformation to be applied after layouting.	No	Yes
Render Transformation Origin	Sets the render transform origin in relative coordinates.	No	Yes
Reversed	Defines whether the stack layout arranges its items in reverse order.	No	Yes
Right Image	The image to use in the center-right.	No	Yes
Roughness Factor	Sets the roughness of the material: 0 represents a smooth, glossy surface, and 1 represents a rough, diffuse surface.	No	Yes
Roughness Texture	Sets the texture that contains a roughness map for the material. Kanzi reads the roughness from the Green channel of the texture. Use the Roughness Factor property to scale the roughness from this texture.	No	Yes
Row	The row into which grid layout places the item.	No	Yes
Row Span	Defines the number of rows an item in a grid layout occupies.	No	Yes
Selected	Indicates whether the List Box item held by this List Box Item Container is selected. The List Box sets the value of this property.	No	Yes
Selected Item Index	Sets the index of the item that is currently selected in the List Box node. A List Box node updates this property when the user scrolls that List Box node. By setting the value of this property to the index of the item that you want to select in a List Box, you can select that item.	No	Yes
Shadow Angle	Sets the direction of the shadow as an angle relative to the positive x axis. The default is 45 degrees. When you set the Override Shadow Offset property, this property has no effect.	No	Yes
Shadow Blur Radius	Sets the softness of the shadow by defining the distance in pixels the shadow blur extends outward from an edge. For a shadow with sharp edges, set to 0. The default is 8 pixels.	No	Yes
Shadow Color	Sets the color and alpha of the shadow.	No	Yes
Shadow Distance	Sets how far to move the shadow from the object in the direction set by the Shadow Angle property. The default is 10 pixels. When you set the Override Shadow Offset property, this property has no effect.	No	Yes
Shadow Only	Whether to render only the shadow without the node contents.	No	Yes
Shadow Quality	Sets the visual quality of the shadow. Lower quality uses less computing and memory resources.	No	Yes
Shadow Type	Sets the type of the shadow: - Drop Shadow appears behind or below objects. - Inner Shadow appears inside objects.	No	Yes
Side	The docking side of an item in the dock layout.	No	Yes
Snap Character To Pixel	Sets whether Kanzi positions characters in 2D rendering to the nearest pixel: - When enabled, text sharpness improves, but some characters can shift a fraction of a pixel. - When disabled, certain combinations of screen resolution, use of anti-aliasing, and font size can cause the text to appear blurry. In that case, you can improve the appearance of the text with the Fractional Character Width and Character Spacing properties.	No	Yes
Snap to Pixel	Snap the translation of the node and its size into pixel boundary.	No	Yes
Specular Anti-Aliasing Strength	Sets the strength of the specular anti-aliasing effect. Higher value results in blurrier specular highlights. For no specular anti-aliasing, set the value to 0. For full specular anti-aliasing, set the value to 1. The default value is 0.25.	No	Yes
Specular Anti-Aliasing Threshold	Sets the upper limit for the amount of specular anti-aliasing effect to apply. The default value is 0.18.	No	Yes
Specular Color	The color of the specular reflection.	No	Yes
Specular Color Factor	Sets the specular color for the material.	No	Yes
Specular Color Texture	Sets the texture that contains the specular color for the material. Use the Specular Color Factor property to filter the value from this texture.	No	Yes
Specular Exponent	Determines the size of the specular highlight.	No	Yes
State Manager	Sets the State Manager to the node.	No	Yes
Step Value	The minimum amount that the value of the range can change at a time.	No	Yes
Stretch	Whether to scale this Trajectory Layout to match the layout size.	No	Yes
Style	Sets a style to the node.	No	Yes
Tags	List of tags attached to the item	No	No
Text	Sets the text content that the text node renders. To create a line break press Shift+Enter.	No	Yes
Text Horizontal Alignment	Sets the horizontal alignment of the text.	No	Yes
Text Vertical Alignment	Sets the vertical alignment of the text.	No	Yes
Texture	The texture of the material.	No	Yes
Texture 0	Sets the first texture you want the Blit Render Pass to blit.	No	Yes
Texture 1	Sets the second texture you want the Blit Render Pass to blit.	No	Yes
Texture 2	Sets the third texture you want the Blit Render Pass to blit.	No	Yes
Texture 3	Sets the fourth texture you want the Blit Render Pass to blit.	No	Yes
Texture Offset	Sets an offset for texture in materials.	No	Yes
Texture Tiling	Determines the number of times a texture is presented in a material.	No	Yes
Toggle State	Sets the toggle state of the Button.	No	Yes
Toggle State Count	Sets the number of toggle states of the Button.	No	Yes
Tone Map Linear Scale	Sets the scale for the linear tonemap option for the material. When linear tonemapping is used, Kanzi divides all output color by the value of this property.	No	Yes
Top Image	The image to use in the middle of the top row.	No	Yes
Top-Left Image	The image to use in the top-left corner.	No	Yes
Top-Right Image	The image to use in the top-right corner.	No	Yes
Trajectory Override Offset	Sets the offset of an item in a Trajectory Layout. When you do not set this property, the Trajectory Layout sets the offset.	No	Yes
Transition Phase	The phase of the transition. For example, use for pixel-based effects.	No	Yes
Truncation	Sets how Kanzi truncates text when either Truncation or Overflow property is set and the text does not fit in this node: - None disables text truncation. - At character truncates text character by character. Default value. - At word truncates text by entire words.	No	Yes
Truncation Direction	Sets which part Kanzi truncates when either the Truncation or Overflow property is set and the text does not fit in this node: - Trailing truncates single- and multiline text at the end. Default value. - Center truncates single-line text in the middle. For multiline text, truncates entire lines from the middle, if the text does not fit in the height of this node, and clips text that does not fit in the width of this node. - Leading truncates single-line text in the beginning. For multiline text, truncates entire lines from the beginning, if the text does not fit in the height of this node, and clips text that does not fit in the width of this node.	No	Yes
Two Pass Rendering	Defines whether the Text Block 3D is rendered in two passes. Disabling the two pass rendering improves performance, but can cause invalid rendering results when glyph bounds overlap.	No	Yes
Use Screen Space	Whether to layout the mask relative to the screen instead of the node.	No	Yes
Value	The current value.	No	Yes
Vertical Alignment	The alignment in vertical direction the node should use when it resides under a layout.	No	Yes
Vertical Margin	Sets the vertical space between this node and other nodes that are adjacent to this node in a layout. To set the Vertical Margin property fields in a binding use: - Vector_X to access the Bottom property field - Vector_Y to access the Top property field	No	Yes
Vertical Padding	Sets the padding spaces between the content and the top and bottom boundaries of the Text node.	No	Yes
Visible	When disabled, Kanzi does not render the node.	No	Yes
Visible Amount in Parent	Sets the amount the node is inside its parent. Use the value of this property in shaders to implement fades. Calculated by the parent node.	No	Yes
Word Wrap	Sets whether to break long lines into multiple lines to make the text fit within the boundaries of the Text Block node.	No	Yes

Text Block 2D messages

Name	Description	Inherited	Exported to Kanzi Engine
Activity Host: Activity Prefab Attached	An Activity Host sends this message when it attaches the prefab of the Activity that is activated.	No	Yes
Activity Host: Activity Prefab Detached	An Activity Host sends this message when it detaches the prefab of the Activity that is deactivated.	No	Yes
Activity: Activated	An Activity sends this message when it is activated.	No	Yes
Activity: Activating	An Activity sends this message when it is in the activating state.	No	Yes
Activity: Deactivated	An Activity sends this message when it is deactivated.	No	Yes
Activity: Deactivating	An Activity sends this message when it is in the deactivating state.	No	Yes
Activity: Status Changed	An Activity sends this message when the value of its Activity Status property changes.	No	Yes
Animation Player: Completed	Occurs when animation player completes animation playback.	No	Yes
Animation Player: Started	Occurs when animation player starts animation playback.	No	Yes
Animation Player: Stopped	Occurs when animation player stops animation playback.	No	Yes
Button: Cancel	Occurs when a user lifts their finger outside of a Button that they previously pressed.	No	Yes
Button: Click	Occurs when a user lifts their finger on top of a Button that they previously pressed and when the time set by the Auto Press Interval property in the pressed Button expires.	No	Yes
Button: Down	Occurs when the user presses down the Button.	No	Yes
Button: Enter	Button: Enter trigger is set off: - When the user presses down the button. - When the user presses down the button, moves the pointer outside of the button area, and then moves the pointer back to the button area while still holding down the pointer.	No	Yes
Button: Leave	Button: Leave trigger is set off: - When the user presses down the button and then lifts the pointer. - When the user presses down the button and then moves the pointer outside of the button area. - When the user sets off a Button : Long Press trigger.	No	Yes
Button: Long Press	Occurs when the user presses down a Button and holds the Button pressed for the amount of milliseconds defined in the Hold Interval property of that Button.	No	Yes
Click: Begin	Occurs when the user presses a hit-testable node with a Click Manipulator. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Click: Cancel	Occurs when the user first presses a hit-testable node with a Click Manipulator, then moves the pointer outside of the node area, and lifts the pointer. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Click: Click	Occurs when the user presses and releases a hit-testable node with a Click Manipulator, while the pointer is still within the node area and Kanzi does not recognize another gesture. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Click: Enter	Occurs when the user presses a hit-testable node with a Click Manipulator and then every time the user moves the pointer on top of that node while still holding down the pointer. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Click: Leave	Occurs when the user presses a hit-testable node with a Click Manipulator and then every time the user moves the pointer outside of that node. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Command: Command	Command message arguments	No	Yes
Data Trigger	Monitors changes in properties and data source values. Use a Data Trigger to apply an action to either set a property value of a target node or activate an Activity node.	No	Yes
Drag and Drop Manipulator: Drag and Drop Canceled	Occurs when focus moves away from the node during the drag-and-drop gesture.	No	Yes
Drag and Drop Manipulator: Drag and Drop Finished	Occurs when the user lifts their finger after starting the drag-and-drop gesture.	No	Yes
Drag and Drop Manipulator: Drag and Drop Moved	Occurs when the user moves their finger after starting the drag-and-drop gesture.	No	Yes
Drag and Drop Manipulator: Drag and Drop Started	Occurs when the user holds their finger for 500ms on the node.	No	Yes
Focus: About To Gain Focus	Kanzi sends this message before a focusable node receives focus.	No	Yes
Focus: About To Lose Focus	Kanzi sends this message before the focused node loses focus.	No	Yes
Focus: Focus Entered Focus Scope	When focus enters a focus scope, Kanzi sends this message to the focus scope node that contains the node that gains focus.	No	Yes
Focus: Focus Gained	Kanzi sends this message to the node that received focus.	No	Yes
Focus: Focus Left Focus Scope	When focus leaves a focus scope, Kanzi sends this message to the focus scope node that contains the node that loses focus.	No	Yes
Focus: Focus Lost	Kanzi sends this message to the node that lost focus.	No	Yes
Focus: Input Outside Overlay	Kanzi sends this message to an overlay focus scope when the application area outside the boundaries of that overlay receives input.	No	Yes
Focus: Overlay Brought To Front	Occurs when an overlay focus scope becomes the foremost overlay scope in the overlay focus scope stack.	No	Yes
Focus: Overlay Gained Focus	When an overlay scope gains focus, Kanzi sends this message to the overlay scope node that contains the node that gains focus.	No	Yes
Focus: Overlay Lost Focus	When an overlay scope loses focus, Kanzi sends this message to the overlay scope node that contains the node that loses focus.	No	Yes
Focus: Overlay Sent To Back	Occurs when an overlay focus scope is no longer the foremost overlay scope in the overlay focus scope stack.	No	Yes
Focus: Scope Brought To Front (deprecated)	Occurs when an overlay focus scope is brought to front. Deprecated. Use Overlay Brought To Front instead.	No	Yes
Focus: Scope Sent To Back (deprecated)	Occurs when a foremost overlay focus scope is sent to back. Deprecated. Use Overlay Sent to Back instead.	No	Yes
Key Input: Key Canceled	Occurs when Kanzi recognizes a key-canceled gesture. A key-canceled gesture occurs when Kanzi recognizes that the user canceled a gesture.	No	Yes
Key Input: Key Navigation Canceled	Occurs when the key-pressed gesture is canceled for the navigation direction.	No	Yes
Key Input: Key Navigation Finished	Occurs when Kanzi recognizes the key-released gesture for the navigation direction. To capture key navigation gestures for a node, create a Navigation Manipulator component in that node.	No	Yes
Key Input: Key Navigation Started	Occurs when Kanzi recognizes the key-pressed and key repeat gestures for the navigation direction. To capture key navigation gestures for a node, create a Navigation Manipulator component in that node.	No	Yes
Key Input: Key Pressed	Occurs when Kanzi recognizes a key-pressed gesture. A key-pressed gesture occurs when Kanzi recognizes a key event that contains all the elements that compose that gesture.	No	Yes
Key Input: Key Released	Occurs when Kanzi recognizes a key-released gesture. A key-released gesture occurs when Kanzi recognizes the release of one of the elements that compose that gesture.	No	Yes
List Box: Item Hidden	Occurs when an item is unloaded from the working memory. To set how many items you want to keep loaded in the working memory at a time, use the Keep Alive Item Count property.	No	Yes
List Box: Item Selected	Occurs when an item is selected.	No	Yes
List Box: Item Visible	Occurs when an item is loaded to the working memory. To set how many items you want to keep loaded in the working memory at a time, use the Keep Alive Item Count property.	No	Yes
List Box: Scroll Finished	Occurs when the List Box stops scrolling.	No	Yes
List Box: Scroll Started	Occurs when the List Box starts to scroll.	No	Yes
List Box: Scrolled	Occurs when the List Box scrolls.	No	Yes
List Box: Target Changed	Occurs when List Box gets a new target item.	No	Yes
List Box: User Scroll Finished	Occurs when the application user stops scrolling the List Box.	No	Yes
List Box: User Scroll Started	Occurs when the application user starts to scroll the List Box.	No	Yes
Long Press: Long Press	Occurs when the user presses a hit-testable node with a Long-Press Manipulator and holds the press for the time that you set in the Long-Press Manipulator. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Long Press: Long Press Cancel	Occurs during the long-press gesture when the user moves the focus away from a hit-testable node with a Long-Press Manipulator. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Message Trigger		No	Yes
Multi-Click: Intermediate Click	Occurs when the user presses and releases a hit-testable node with a Multi-Click Manipulator that is set to send messages for intermediate clicks. To set a Multi-Click Manipulator to send messages for intermediate clicks, in the Multi-Click Manipulator enable the Send Intermediate Click Messages property. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Multi-Click: Multi-Click	Occurs when the user presses and releases a hit-testable node with a Multi-Click Manipulator a specified number of times (default 2) within a set amount of time (default 250 ms) between presses. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
Multi-Click: Multi-Click Canceled	Occurs during the multi-click gesture when the user moves the focus away from a hit-testable node with a Multi-Click Manipulator. You cannot use this trigger with nodes that handle input by default, such as Button and Toggle Button nodes.	No	Yes
On Attached	This trigger is set off when the item is initialized. For example, when you add a node to the node tree, or enter a state that contains this trigger.	No	Yes
On Property Change	Occurs when a property is changed	No	Yes
On Timer	Occurs when timer interval is elapsed	No	Yes
Page Host: Page Navigation Finished	Page host has finished navigation process.	No	Yes
Page Host: Page Navigation Started	Page host has started navigation process.	No	Yes
Page: Activated	Page has been activated.	No	Yes
Page: Deactivated	Page has been deactivated.	No	Yes
Pan Manipulator: Pan Canceled	Occurs when focus moves away from the node during the pan gesture.	No	Yes
Pan Manipulator: Pan Entered	Occurs when the pan gesture enters the node the manipulator is attached to.	No	Yes
Pan Manipulator: Pan Finished	Occurs when the user lifts their finger after Kanzi recognizes a pan gesture.	No	Yes
Pan Manipulator: Pan Left	Occurs when the pan gesture leaves the node the manipulator is attached to.	No	Yes
Pan Manipulator: Pan Moved	Occurs when the user changes the position of their finger and that change exceeds the recognition thresholds.	No	Yes
Pan Manipulator: Pan Started	Occurs when the user presses down their finger on the node. If the user lifts their finger before exceeding the position change threshold, Kanzi cancels the pan gesture.	No	Yes
Pinch Manipulator: Pinch Canceled	Occurs when focus moves away from the node during the pinch gesture.	No	Yes
Pinch Manipulator: Pinch Finished	Occurs when the user lifts their finger after Kanzi recognizes a pinch gesture.	No	Yes
Pinch Manipulator: Pinch Moved	Occurs when the user changes the position of their finger and that change exceed the scale or rotation threshold.	No	Yes
Pinch Manipulator: Pinch Started	Occurs when the user presses down their finger. If the user lifts their finger before it exceeds the scale or rotate threshold, Kanzi cancels the pinch.	No	Yes
Prefab View: Asynchronous Load Completed	Occurs when asynchronous loading of resources from a prefab has been finished.	No	Yes
Property Target Easing Interpolator: Easing Interpolation Completed	Occurs when Property Target Easing Interpolator completes its interpolation.	No	Yes
Property Target Interpolator: Interpolation Completed	Occurs when property target interpolator completes interpolation.	No	Yes
Range: Value Change Finished	Occurs when the range value stops changing.	No	Yes
Range: Value Change Started	Occurs when the range value starts changing.	No	Yes
Range: Value Changed	Occurs when the range value has changed.	No	Yes
Scroll View: Scroll Ended	Occurs when the scroll position of a Scroll View node stops changing.	No	Yes
Scroll View: Scroll Started	Occurs when the scroll position of a Scroll View node starts changing.	No	Yes
Scroll View: Scroll Zoomed	Occurs when the zoom level of a Scroll View node changes.	No	Yes
Scroll View: Scrolled	Occurs when the scroll position of a Scroll View node changes.	No	Yes
Scroll View: Snap Request	Occurs when a Scroll View node requests snapping target from the hosting component.	No	Yes
Scroll View: User Scroll Ended	Occurs when the user stops scrolling a Scroll View node.	No	Yes
Scroll View: User Scroll Started	Occurs when the user starts scrolling a Scroll View node.	No	Yes
State Manager: Entered State	Occurs when a state manager has entered a state.	No	Yes
State Manager: Left State	Occurs when a state manager has left a state.	No	Yes
State Manager: Transition Finished	Occurs when a state manager finishes a transition to a state.	No	Yes
State Manager: Transition Started	Occurs when a state manager begins a transition to a state.	No	Yes
Text Box: Composition Text Changed	Occurs when the text produced in an Input Method Editor is updated in a Text Box node.	No	Yes
Text Box: Composition Text Committed	Occurs: - When the text produced in an Input Method Editor is committed to the cached text in a Text Box node. - When a trigger executes the Commit Composition Text action.	No	Yes
Text Box: Cursor Moved	Occurs when the user moves the cursor in a Text Box node.	No	Yes
Text Box: Editing Finished	Occurs when a Text Box node leaves the editing state after the user modified the text content.	No	Yes
Text Box: Editing Started	Occurs when the user makes the first modification to the text in a Text Box node that is in the editing state.	No	Yes
Text Box: Entered Editing State	Occurs when a Text Box node enters the editing state.	No	Yes
Text Box: Input Method Action	Occurs when the user taps the action button on their on-screen keyboard while editing the text in a Text Box node.	No	Yes
Text Box: Input Method Available	Occurs when an input method becomes available to a Text Box node. For example, an on-screen keyboard becomes available when it appears on the screen.	No	Yes
Text Box: Input Method Unavailable	Occurs when the input method that is composing text in a Text Box node becomes unavailable. For example, an on-screen keyboard becomes unavailable when the user hides it.	No	Yes
Text Box: Left Editing State	Occurs when a Text Box node leaves the editing state	No	Yes
Text Box: Selection Changed	Occurs when the user changes the text selection in a Text Box node.	No	Yes
Text Box: Selection Cleared	Occurs when the user clears or resets the text selection in a Text Box node.	No	Yes
Text Box: Selection Started	Occurs when the user starts selecting text in a Text Box node.	No	Yes
Text Box: Text Changed	Occurs when the user changes the text in a Text Box node.	No	Yes
Text Box: Text Composition Canceled	Occurs: - When the text composition in a Text Box node is canceled by Input Method that is in text composition state. - When a trigger executes the Cancel Text Composition action.	No	Yes
Toggle Button Group: Toggled	Occurs when the toggle state of a Toggle Button node in a Toggle Button Group node changes.	No	Yes
Toggle Button: State Toggled	Occurs when the toggle state of the Button changes.	No	Yes
Toggle Button: Toggled Off	Occurs when the Button is toggled off.	No	Yes
Toggle Button: Toggled On	Occurs when the Button is toggled on.	No	Yes

See also

Using the Text Block nodes